Файл: 92FWD_7.pdf

Throughout this group, references may be made to a particular vehicle by letter or number designation. A chart showing the breakdown of these designations is included in the Introduction Section at the front of this service manual.

COOLING SYSTEM

The cooling system consists of an engine cooling module, thermostat, coolant, a water pump to circulate the coolant. The engine cooling module may consist of a radiator, electric fan motor, shroud, radiator pressure cap, coolant reserve system, transmission oil cooler, hoses, clamps, air condition condenser, transmission oil lines and charge air cooler.

² When Engine is cold: Thermostat is closed, cooling system has no flow through the radiator. The coolant bypass flows through the engine only.

² When Engine is warm: Thermostat is open, cooling system has bypass flow and coolant flow through radiator.

Its primary purpose is to maintain engine temperature in a range that will provide satisfactory engine performance and emission levels under all expected driving conditions. It also provides hot water (coolant) for heater performance and cooling for automatic transmission oil. It does this by transferring heat from engine metal to coolant, moving this heated coolant to the radiator, and then transferring this heat to the ambient air.

Coolant flow circuits for 2.2L and 2.5L engine equipped vehicles are shown in (Fig 1). Turbocharged equipped engines coolant routing and plumbing are shown in (Fig 2). The 3.0L engine coolant routing is shown in (Fig 3). The 3.3L and 3.8L engine coolant routing is shown in (Fig 5).

TURBOCHARGER COOLANT ROUTING

Engines equipped with a Turbocharger maintain a continuous engine coolant flow through the Turbocharger bearing housing water jacket. Hose and tube assemblies provide a closed loop coolant flow from the cylinder block water jacket to the turbocharger housing and back to the cylinder head waterbox (Fig. 2).

Excluding heated intake manifold hose routing (hose is routed from waterbox directly to heater), all other system functions are essentially the same as shown for standard engines.

During any reassembly procedures all pipe fittings in water jacket, bearing housing and waterbox require cleaning and application of thread sealant for entire length of threads. Tighten all fittings to torque specified in (Fig 2).

WATER PIPESÐ3.0L

The 3.0L engines use metal piping beyond the lower radiator hose to route coolant to the suction side of water pump, located in the V of the cylinder banks.

These pipes are also provided with inlet nipples for thermostat bypass and heater return coolant hos-

es,and brackets for rigid engine attachment. The pipes employ O-rings for sealing at their interconnection and to the water pump (Fig. 4).

WATER PUMPS

A quick test to tell whether or not the pump is working is to see if the heater warms properly. A defective pump will not be able to circulate heated coolant through the long heater hose.

The water pump on all models can be replaced without discharging the air conditioning system.

WATER PUMPÐ2.2/2.5L ENGINE

The 2.2/2.5L engine water pump has a diecast aluminum body and housing with a stamped steel impeller. The 2.2/2.5L pump uses an O-ring gasket between body and housing. The assembly bolts directly to the block. Cylinder block to water pump sealing is provided by a rubber O-ring.

(2)If equipped with air conditioning, see Solid Mount Accessory Bracket in (Standard Service Procedures) Group 9, Engine:

(a)Remove air conditioning compressor and alternator from solid mount bracket and set aside.It is not necessary to discharge the a/c system.

(b)Remove solid mount bracket.

(3)If the vehicle is not equipped with air conditioning, remove alternator and mounting bracket.

(4)Disconnect lower radiator and heater hoses from pump.

(5)Remove water pump attaching screws to engine (Fig. 1). Turbo III has a spacer between the water pump and block on the lower screw.

DISASSEMBLY

(1)Remove three screws holding pulley to water pump.

(2)Remove nine screws holding water pump body to housing. Remove the pump body from housing (Fig. 2).

(3)Clean gasket surfaces on water pump housing and engine block.

(4)Remove and discard O-ring gaskets and clean O-ring grooves.