Файл: SF Trilogy Manual - PRESS REVISED.pdf

Autococker® Trilogy Select-Fire Manual

WORR GAME PRODUCTS, LLC.

TRILOGY® AUTOCOCKER® OWNERS MANUAL

WARNING:

This is not a toy. Misuse may cause serious injury or death. Eye protection designed specifically for paintball must be worn by the user and persons within range. Recommend 18 years or older to purchase. 14 years old to use with adult supervision or 10 years old to use on paintball fields meeting ASTM-standard F1777-97. READ OPERATION MANUAL BEFORE USING.

WARNING:

Never shoot at anyone without proper protective equipment for eyes, ears, throat and head, which must be worn at all times. Eye protection must be designed specifically for paintball use. Failure to follow these safety precautions may result in bodily injury including blindness and deafness.

© Copyright 2004 Worr Game Products, LLC. All rights reserved.

Autococker® Trilogy Select-Fire Manual

W’elcome to the world of Autocockers, and thank you for your purchase of a new Autococker® marker. You will now be able to experience paintball at its highest level.

Table of Contents

Colors and parts may vary from illustrations. Worr Game Products reserves the right to change parts at any time. Worr Game Products, Autococker®, Cocker and the WGP logo are all registered to WGP LLC. ©2004 WGP LLC.

Autococker® Trilogy Select-Fire Manual

I. Rules of Safe Paintball Marker Handling.

Your Autococker®marker is not a toy.

18 years old to purchase. 14 years old to play with adult supervision or 10 years old to use on paintball fields meeting ASTM-standard F1777-97. Respect other peoples’ property and when using the Autococker® marker, obey all local, state and federal laws. When entering a paintball field, become aware of their rules and regulations. It is very important to have the proper paintball protection before going to the paintball field for play. This includes and is not limited to eye, head, throat, and body protection. All protection used should be designed for the sport of paintball, e.g.: eye gear designed specifically for paintball usage.

Always have a barrel plug or barrel sock in place and keep the safety ON when handling your marker. When repairing or cleaning your marker first remove barrel and gas cylinder, then depressurize your marker by pointing in safe direction and dry-firing. Always treat the paintball marker as if it were loaded. When handling the marker, always keep your fingers or any other objects away from the trigger assembly to avoid accidental discharges. Make sure when carrying or transporting the marker, to keep the muzzle pointed downward with a barrel blocking device in place. Before transporting your marker through public areas, such as airports, or bus and trains stations, call ahead for regulatory information regarding the carrying and transporting of such an item.

Remember, the Autococker® marker should never be pointed or fired at anyone without the proper paintball approved eye and face protection, and should only be used at a supervised, licensed and insured paintball fields.

NOTE: A safe environment is an area where you and everyone within 200 yards is wearing paintball approved safety goggles and equipment. An area that is netted in and meets ASTM-standard F1777-97.

Autococker® Trilogy Select-Fire Manual

I. Rules of Safe Paintball Marker Handling.

•Treat every marker as if it were loaded.

•Never look down the barrel of a paintball marker.

•Keep your finger off the trigger until ready to shoot.

•Never shoot a person not wearing proper protection.

•Never point the marker at anything you don’t wish to shoot, even if it is not loaded and there is no air source attached.

•Keep the marker on safe until ready to shoot.

•Keep the barrel blocking device in/on the marker when not shooting.

•Always remove paintballs and propellant source before disassembly.

•After removing propellant source, point marker in safe direction and discharge until marker is degassed.

•Store the marker unloaded and degassed in a secure place.

•Follow warnings listed on propellant source for handling and storage.

•Do not shoot at fragile objects such as windows.

•Every person within range must wear eye, face and ear protection designed specifically to stop paintballs.

•Always measure your marker’s velocity before playing paintball and never shoot at velocities in excess of 300 feet per second.

•Never engage in vandalism.

•Do not modify your markers air system or regulators in any way.

•Do not use any paintball marker for drive-by shootings.

•Faliure to follow these safety precautions may result in bodily injury including blindness and death.

Autococker® Trilogy Select-Fire Manual

II. Preparing for Usage

1.Screw barrel onto marker

2.Place barrel blocking device properly onto the marker

3.Pull the cocking rod back until it latches into place

4.Make sure the safety is pushed to the “PUSH SAFE” position.

5.Connect the tank to the ASA (air system adapter.)

NOTE: Make sure to always get your cylinders filled by authorized, skilled and knowledgeable technicians for the correct fill limits of each cylinder. Do not try to refill cylinders by yourself. Do not use cylinders that have not been properly maintained or that are damaged. WGP recomends compressed air but C02 will work. Always be sure to only use ASTM compliant tanks for your marker. Always use caution when refilling, attaching and handling any type of air tank.

6.Attach the loader to the feed port of the marker

NOTE: Use only 0.68 caliber paintballs in your Worr Game Products Autococker® marker. All WGP Autococker® markers are timed and tested prior to leaving the factory.

Before field use, ensure the velocity is in compliance with field safety guidelines. General field velocity limits are usually between 250-300 fps (feet per second). Your paintball markers velocity should never exceed 300 fps. Observe and abide by all local laws, regulations and field safety guidelines pertaining to the use of paintball markers.

WARNING:

Always wear paintball approved eye and face protection when dealing with a pressurized paintball marker.

Autococker® Trilogy Select-Fire Manual

Marker Schematic

BARREL

FEED TUBE

PULL PIN

BOLT

COCKING ROD

SAFETY

TRIGGER PUSH FIRE

PUSH SAFE

ASA (AIR RECEIVER)

If you experience a problem with your Trilogy, please contact WGP for service.

DO NOT RETURN TO PLACE OF PURCHASE.

Autococker® Trilogy Select-Fire Manual

II. Preparing for Usage

Sequence Of Operations:

When you pull the trigger, it activates a micro switch which tells the processor on the board to activate the internal electronic valve. This valve fills the ram inside the grip frame. The ram lowers the sear, which releases the hammer. The hammer strikes the valve, which allows gas to flow through the bolt and down the barrel, propelling a ball out. As you continue to pull the trigger, the 3 way shifts the flow of air from the rear to the front of the ram. The incoming air drives the ram rearward which causes the pump arm to push the bolt, cocking rod, and cocking block backwards. Note that the bolt and cocking assembly will remain in the rearward position until the trigger is fully released. This action allows a ball to drop into the breach and at the same time completes the re-cocking process. At this point, the marker has completed one full cycle and is once again ready for use.

Note: If you are using a C02 tank, you need to be aware that C02 has some limitations. If you play in a cold environment and you fire rapidly you may experience rapid fluctuations in velocity (shoot down) or you may experience “marker freeze up”. This is normal for C02. C02 is a frozen liquid, and as you shoot the marker rapidly you are firing this frozen liquid into the marker causing the marker to freeze up. The remedy for this problem is to allow the marker and tank to warm-up to room temperature. WGP suggests the use of compressed air when shooting rapidly or in cold weather.

WARNING:

Do not put any part of your body directly in back of the cocking block when you activate the trigger.

Autococker® Trilogy Select-Fire Manual

II. Preparing for Usage

•Paintball industry approved protective gear (for face and eyes) must be worn at all times while operating and performing adjustments on this marker.

•Do not insert objects into the space between the cocking block and the main body of the marker at any point in time. Improper marker treatment may result

in damage to the marker and serious injury to the operator.

•Prior to beginning any work on your marker, check to make sure that all excess pressure has been released by pointing the marker in a safe direction and pulling the trigger. This is a necessary precaution due to the fact that the marker may still contain pressure even after the removal of the gas source.

•Damages to the marker due to improper adjustments are NOT covered under warranty. If you are uncertain, unable or do not know how to perform work on the marker, have adjustments and repairs made by WGP.

Turning On and Off the Electronics:

To turn on the marker, press and hold the button until the led lights up. For semi mode, the marker will flash green quickly. To turn the eye system off — press and hold the button; the LED will turn solid yellow. Release the button — the eye system has now been turned off. When the eye system is off the LED will flash slowly. To turn the marker off, press and hold the button until the LED goes solid yellow then solid red and release.

III. Velocity

WARNING:

WGP does not set the velocity prior to leaving the factory. You MUST set the velocity within field and safety limits using a chronograph prior to playing. Always use a chronograph to verify that your markers velocity does not exceed maximum safety limits.

Autococker® Trilogy Select-Fire Manual

III. Velocity

To Adjust Velocity:

1.Remove the cocking rod by unscrewing it counterclockwise.

2.Insert the provided 3/16” Allen wrench in place of the cocking rod so that it passes through the IVG (Internal Velocity Governor). Turning the Allen wrench clockwise will increase the velocity while counterclockwise will decrease the velocity.

3.Movement of the wrench quarter turn in either direction will change your velocity approximately 15-20 fps (feet per second).

IVG should not be deeper + than 1/4” — 1/2” inside

of receiver

3/16” Allen Wrench

Back View

Autococker® Trilogy Select-Fire Manual

IV. Cleaning Your Marker

It isn’t necessary to completely disassemble your marker to clean it. WGP recommends the following cleaning be done after each day of play:

1.Before you start ALWAYS make sure that all paintballs are out of the marker.

2.Remove air source and ensure that all air has been released from the marker.

3.Remove the barrel sock and then remove the barrel.

4.Lightly spray marker down with a 50-50 mix of rubbing alcohol and water and then wipe down.

5.Wipe down the marker with a clean cloth, or blow off the marker with compressed air (NOT CO2).

6.Remove bolt and lubricate bolt O-rings with petroleum jelly or lithium grease, then reinstall.

7.Lubricate all moving parts with Vaseline, and reassemble.

8.WGP recommends that after every 4-5 days of play you place 3-4 drops of 3 in 1 or other paintball marker specific oil in the air receiver and fire the marker 10-15 times without the barrel. This will distribute the oil throughout the marker and lubricate the internals.

Factory Approved Lubricants:

WARNING:

Always make sure you and everyone around you wears protection when you clean the marker or check it for paintballs.