Файл: Staliunas K., Sanchez-Morcillo V.J. (eds.) Transverse Patterns in Nonlinear Optical Resonators(ST.pdf

92 6 Resonators with Curved Mirrors

laser patterns (Sect. 6.2). In Sect. 6.3 the case of a resonator with strongly curved mirrors is investigated, which in some limits (confocal and self-imaging resonators) also leads to important simplifications of the problem.

6.1 Weakly Curved Mirrors

In this case the e ects of the curvature may be treated perturbatively. We can take into account of these e ects by assuming a weakly varying detuning in the transverse cross section of the resonator, ω(r) = ω0 +cr2. We then (see Fig. 6.1) consider a resonator with focusing parabolic mirrors as a resonator with a length thats varies over the transverse cross section: the resonator is of maximum length along the optical axis, and shorter at some distance from it. This corresponds to a negative detuning that is maximum on the optical axis and decreases away from it.

Fig. 6.1. A resonator with focusing curved mirrors can be considered as a resonator with laterally varying length: on the optical axis the length of the resonator is maximum

If the variation of the resonator length over the beam width is small, then the derivation of the order parameter equation is straightforward. We can repeat the adiabatic-elimination procedure in Chap. 2 by using a coordinate-

The same result was obtained in [1] by using a multiscale expansion. In both derivations the smallness parameter is ε = √ac, which is actually the

resonator without gain or decay. The eigenfunctions of the propagator ˆ are

P the transverse modes of the resonator, such that the field distributions do

94 6 Resonators with Curved Mirrors

The mode expansion is not very useful if many modes are taken into account. The computer time required to integrate (6.8) numerically is proportional to the fourth power of the number of modes. Therefore, for a large number of modes, the numerical integration of the partial di erential equation (6.3) is usually more convenient. However, the mode expansion approach is very useful if a small number of modes is excited. The usefulness of mode expansion is illustrated below with two examples of circling vortices, and with an example of transverse-mode locking.

6.2.1 Circling Vortices

Vortices circling around the optical axis of a laser can be interpreted as the interference of two modes of di erent helicities. In this case, (6.8) becomes

From (6.10), one can analyze the behavior of two modes with di erent helicities. For example, it is found that the frequencies of the modes are not a ected by the nonlinear interaction. The particular spatial shapes of the helical modes do not lead to nonlinear mode pulling or locking. The variation of the di erence between the phases of the modes only rotates the two-mode interference pattern around the optical axis of the laser, and consequently there is no preferred phase di erence.

There are several di erent solutions for the intensities of the modes ni = |fi|2. One solution is trivial, with the amplitudes of both modes equal to zero. This solution is, however, unstable if the laser is above the generation threshold. Another solution corresponds to a single mode, where the intensity of one mode is zero, and the intensity of the other is ni = pi/Gii. The most interesting solution is that where both modes are excited,

A stability analysis of these solutions shows that the two modes can coexist (and beat, if they have di erent eigenfrequencies) if G11G22 > 4G212, which means that the modes overlap relatively weakly. For example, the fundamental mode TEM00 and the single-vortex mode TEM01 overlap relatively

strongly and the above inequality is invalid. The overlap between these two

√ √

modes is G12/ G11G22 = 1/ 2, which is larger than the critical overlap of 1/2 for the coexistence of modes. These two modes, therefore, cannot exist simultaneously. Interference of the modes TEM00 and TEM01 results in an optical vortex rotating around the optical axis of the laser. Such behavior is, however, unstable for a class A laser, as (6.12) shows, and either the vortex spirals in and subsequently remains on the optical axis of the laser (the helical TEM01 mode wins the competition), or the vortex spirals out and disappears (the fundamental TEM00 mode wins). A steadily spiraling vortex is possible only in a class B laser, as shown in Chap. 7.

Instead of one single vortex, however, several circling vortices are easily obtained in the framework of (6.11). A number l of vortices of the same charge arranged symmetrically around the optical axis of the laser corresponds to

the interference pattern of a TEM0l mode with the fundamental Gaussian

mode. The mode overlap decreases with increasing l. For example, the overlap

√

between the TEM02 and√TEM00 modes is 1/ 6, that between the TEM03 and TEM00 modes is 1/ 20, and so on.

In Fig. 6.2, an example of multiple circling vortices is shown, taken from [2]. Note that while multiple circling vortices are relatively easily obtained experimentally, a single circling vortex following a circular trajectory has never been observed.

Fig. 6.2. Three vortices circling around the optical axis of a laser. At the right, an interference picture with a tilted plane wave is shown. The interference fringes indicate the topological charges of the vortices

6.2.2 Locking of Transverse Modes

Another example concerns the locking of the transverse modes. In this case, instead of helical modes (6.4), a expansion into flowerlike modes is more convenient:

(6.13)