ВУЗ: Не указан
Категория: Не указан
Дисциплина: Не указана
Добавлен: 20.12.2024
Просмотров: 181
Скачиваний: 1
13 - 8 FRAME AND BUMPERS |
Ä |
|
Fig. 19 Rear Bumper and FasciaÐAJ-Vehicle
REAR BUMPERÐAP-VEHICLE
REMOVAL (FIG. 20)
(1)Raise vehicle and support on safety stands.
(2)Support rear bumper on lifting device.
(3)Remove bolts holding rear bumper reinforcement to energy absorber units.
(4)Pull rear bumper assembly rearward to disengage retainers from quarter panel.
(5)Separate front bumper from vehicle.
INSTALLATION
Reverse the preceding operation.
Fig. 20 Rear Bumper
REAR BUMPERÐAY-VEHICLE
REAR BUMPER REMOVALÐAY/P-BODY (FIG. 21)
(1) Remove nuts holding fascia to quarter panel ends.
(2)Support bumper assembly on suitable lifting device and remove bolts holding bumper reinforcement to energy absorber units.
(3)Separate bumper from vehicle.
INSTALLATION
Reverse the preceding operation. Align bumper height to fit flush to bottom of tail lamp.
REAR BUMPER OVERHAULÐAY/P-BODY
(1)Position bumper assembly on a suitable padded work surface to avoid damage to painted fascia.
(2)Remove bolts holding bumper face bar to reinforcement and separate face bar from assembly.
(3)Remove push-in fasteners holding fascia to reinforcement.
(4)Remove upper reinforcement to fascia attaching bolts and separate reinforcement from fascia.
To assemble, reverse the preceding operation.
Fig. 21 Rear BumperÐAY/P-Body
REAR BUMPER REMOVALÐAY/S-BODY (FIG. 22)
(1) In luggage compartment, separate liners from quarter panels to gain access to fascia nuts.
Fig. 22 Rear BumperÐAC/S-Body
Ä
(2)Remove nuts holding bumper fascia to quarter panels.
(3)Remove fasteners holding bumper fascia to wheel opening flange.
(4)Disconnect license plate lamp wire connectors.
(5)Remove bolts holding bumper to rear closure panel.
FRAME AND BUMPERS 13 - 9
(6)Remove nuts holding bumper to energy absorber units.
(7)Separate bumper from vehicle.
REAR BUMPER INSTALLATION
Reverse the preceding operation.
FRAME
INDEX
page |
page |
||
Crossmember . . . . . . . . . . . . . . . . . . . . . . . . . . |
. 17 |
General Information . . . . . . . . . . . . . . . . . . . . . . |
. . 9 |
Frame Dimensions . . . . . . . . . . . . . . . . . . . . . . . |
. . 9 |
GENERAL INFORMATION
In this section, references are made to Vehicle Family (Body) codes. To determine the vehicle family identification code, refer to the Introduction Group at the front of this manual.
FRAME DIMENSIONS
Frame dimensions are listed in metric scale then converted to inch scale listed in parenthesis. Engine compartment charts include front suspension upper strut damper mounting tower location. All dimensions are from center to center of Principal Locating Point (PLP), or from center to center of PLP and fastener location.
VEHICLE PREPARATION
Position the vehicle on a level work surface. Using screw or bottle jacks, adjust the vehicle height to the specified PLP dimension above the Datum Line (work surface). Vertical dimensions can be taken from the datum line to the PLP.
ENGINE COMPARTMENT DIMENSIONS
Fig. 1 Engine Compartment DimensionsÐAA-Body
Refer to Fig. 1, 2, 3, 4 or 5.
FRONT FRAME DIMENSIONS
Refer to Fig. 6
REAR FRAME DIMENSIONS
Refer to Fig. 7, 8, 9, 10 or 11.
13 - 10 FRAME AND BUMPERS |
Ä |
|
Fig. 2 Engine Compartment DimensionsÐAC-Body |
Fig. 4 Engine Compartment DimensionsÐAJ-Body |
Fig. 5 Engine Compartment DimensionsÐAP-Body
Fig. 3 Engine Compartment DimensionsÐAG-Body
Ä |
FRAME AND BUMPERS 13 - 11 |
|
Fig. 6 Front Frame DimensionsÐAll
13 - 12 FRAME AND BUMPERS |
Ä |
|
Fig. 7 Rear Frame DimensionsÐAA-Body
Ä |
FRAME AND BUMPERS 13 - 13 |
|
Fig. 8 Rear Frame DimensionsÐAC, AY-Body
13 - 14 FRAME AND BUMPERS |
Ä |
|
Fig. 9 Rear Frame DimensionsÐAG-Body
Ä |
FRAME AND BUMPERS 13 - 15 |
|
Fig. 10 Rear Frame DimensionsÐAJ-Body
13 - 16 FRAME AND BUMPERS |
Ä |
|
Fig. 11 Rear Frame DimensionsÐAP-Body
Ä |
FRAME AND BUMPERS 13 - 17 |
|
Fig. 12 Crossmember
CROSSMEMBER
REMOVAL (FIG. 12)
(1)Hoist vehicle and support on safety stands. Refer to Group 0, Lubrication and Maintenance for proper procedures.
(2)Remove front wheels.
(3)Disconnect lower ball joints from the knuckle assembly. Refer to Group 2, Suspension for proper procedures.
(4)Disconnect power steering hose tie-down from rear upper edge of crossmember, if equipped.
(5)Remove bolts holding steering gear to crossmember. Refer to Group 19, Steering for proper procedures.
(6)Remove bolt holding engine damper strut to crossmember, if equipped with manual transaxle.
(7)Support crossmember on a suitable lifting de-
vice.
(8)Remove nuts holding rear of crossmember to the frame.
(9)Remove bolts holding crossmember to frame from above lower control arms.
(10)Separate the crossmember from the vehicle.
(11)Transfer lower control arms and sway eliminator shaft to new crossmember, if crossmember is being replaced. Refer to Group 2, Suspension for proper procedure.
CROSSMEMBER INSTALLATION
Reverse the preceding operation. delete this line