Файл: 92FWD_23.pdf

23 - 98 AP-BODY

MANUAL WINDOW REGULATOR

INSTALLATION

Reverse the preceding operation.

Fig. 17 Front Door Manual Window

RegulatorÐTypical

FRONT DOOR WINDOW REGULATOR/POWER

POWER WINDOW REGULATOR REMOVAL (FIG. 18)

(1)Remove trim panel and water shield and connect window switch to wire connector.

(2)Raise glass to 25 mm (1 in.) from full up position. Using suitable tape, secure door glass to upper window frame.

(3)Disconnect battery negative cable.

(4)Remove bolts holding window regulator to inner door panel.

(5)Slide roller from window lift channel. Rotate regulator

to bring lift arm through access hole first.

(6)Remove regulator assembly from door.

POWER WINDOW REGULATOR INSTALLATION

Reverse the preceding operation.

REAR DOOR TRIM PANEL

REMOVAL (FIG. 19)

(1)Move glass to down position.

(2)Disconnect battery negative cable.

(3)Remove inside latch release handle bezel. Pull outward at forward edge and push bezel rearward.

(4)Remove screw cover from window crane. Remove screw holding crank to window regulator, if equipped.

(5)Remove screw covers from armrest. Remove screws holding armrest to door.

(6)Disengage frog-leg clips holding trim panel to door. Separate trim panel from door.

(7)Disconnect courtesy lamp wire connector.

Ä

Fig. 18 Front Door Power Window

RegulatorÐTypical

INSTALLATION

Reverse the preceding operation.

Fig. 19 Rear Door Trim Panel

REAR DOOR SILENCER AND WATER SHIELD

REMOVAL (FIG. 20)

(1)Remove door trim panel.

(2)Pull water shield from adhesive around perimeter of door inner panel.

INSTALLATION

Reverse the preceding operation.

REAR DOOR AND HINGE

The rear door hinge is welded to the door and bolted to the B-pillar. The door half of the hinge pivots on a removable hinge pin. The hinge pin is driven in from the bottom on the top hinge and from the top on the bottom hinge. All adjustments to the hinge are performed on the hinge pillar half of the hinge. If the welded half of the hinge must be bent to align door, consult an authorized body repair facility.

Fig. 20 Rear Door Silencer and Water

ShieldÐTypical

REAR DOOR REMOVAL (FIG. 21)

(1)Remove B-pillar trim panel and disconnect all wire connectors leading to door. Push wire harness through access hole in B-pillar into hinge opening.

(2)Support door on a suitable lifting device.

(3)Drive bottom hinge pin upward and remove pin from hinge.

(4)Drive top hinge pin downward and remove pin from hinge.

(5)Separate door from vehicle.

REAR DOOR INSTALLATION

Reverse the preceding operation. The door should not require re-alignment. If door does need alignment, refer to Rear Door Hinge Installation paragraph in this section.

Fig. 21 Rear Door HingesÐTypical

REAR DOOR HINGE REMOVAL (FIG. 21)

(1)To remove upper hinge bolted half, remove B-pillar trim panel. To remove lower hinge bolted half it is not necessary to remove B-pillar trim.

(2)Support rear door on a suitable lifting device.

(3)Drive out hinge pin on the effected hinge.

(4)Remove bolts holding hinge to B-pillar and separate hinge form vehicle.

REAR DOOR HINGE INSTALLATION

Reverse the preceding operation. Align door to achieve 6 mm (0.240 in.) gap to all surrounding panels and flush across gaps.

OUTSIDE REAR DOOR LATCH RELEASE HANDLE

REMOVAL (FIG. 22)

(1)Remove door trim panel, silencer pad, and water shield.

(2)Raise door glass to full up position.

(3)Remove rear door speaker, if equipped.

(4)Disconnect latch release rod from door latch assembly.

(5)Remove nuts holding outside door latch handle to retainer bracket and separate bracket from door.

(6)Separate latch handle from door panel.

INSTALLATION

Reverse the preceding operation.

Fig. 22 Outside Rear Door Latch Release

HandleÐTypical

REAR DOOR LATCH

REMOVAL (FIG. 23)

(1)Remove door trim panel, silencer pad and water shield.

(2)Raise door glass to full up position.

(3)Remove door speaker, if equipped.

(4)Disconnect all actuator rods from door latch assembly.

(5)Remove screws holding door latch assembly to inner door rear panel and separate from door.

INSTALLATION

Reverse the preceding operation.

Fig. 23 Rear Door Latch AssemblyÐTypical

REAR POWER DOOR LOCK ACTUATOR

REMOVAL (FIG. 24)

(1)Remove door trim panel, silencer pad, and water shield.

(2)Raise door glass to full up position.

(3)Remove door speaker, if equipped.

(4)Disconnect actuator rod from door latch assem-

bly.

(5)Remove screws holding power lock actuator to inner door panel and separate from door.

INSTALLATION

Reverse the preceding operation.

Fig. 24-Rear Power Lock ActuatorÐTypical

REAR DOOR GLASS

REMOVAL (FIG. 25)

(1)Remove door trim panel and water shield.

(2)Position door glass half way up in door glass opening.

(3)Pull upward firmly at the front upper corner of glass to disengage lower glass guide from run channel.

(4)Insert door glass removal tool C-4867 between the glass slide and division run channel retaining lip at approximately 50 mm (2 in.) down from top rearward corner of glass. Push handle of tool toward glass to open channel. Pull forward on the glass to separate the slide from the channel.

(5)Position glass inboard of the division channel. Pivot top of glass rearward between division channel and inner door panel.

(6)Separate regulator lift arm roller from glass lift channel or remove bolt from regulator track, with power windows.

(7)Remove door glass through opening at top of

door.

INSTALLATION

(1)Lower door glass into opening at top of door.

(2)Insert window regulator lift arm roller into glass lift channel or install bolt to regulator track, with power windows.

(3)Push top of glass rearward to snap top slide into division run channel.

(4)Push downward at front of glass to snap bottom slide into channel.

(5)Install water shield and trim panel.

Fig. 25 Rear Door Glass

REAR DOOR BELT MOULDING AND WEATHERSTRIP

REMOVAL

(1) Remove trim panel, silencer pad, and water shield.