Файл: 92FWD_23.pdf

GRILLE

REMOVAL (FIG. 1)

(1)Raise hood to the up position.

(2)Remove screws holding grille to grille opening panel.

(3)Separate grille from vehicle.

INSTALLATION

Reverse the preceding operation.

GRILLE OPENING PANEL

REMOVAL (FIG. 1)

(1)Remove grille from grille opening panel.

(2)Remove headlamp assemblies. Refer to Group 8L. Lamps for proper procedures.

(3)Remove bolts holding grille opening panel to closure panel brackets.

(4)Remove bolt holding grille opening panel to brace in front of radiator.

(5)Separate grille opening panel from vehicle.

INSTALLATION

Reverse the preceding operation.

Fig. 1 Grille and Grille Opening Panel

HOOD AND HINGES

HOOD REMOVAL (FIG. 2)

(1)Raise hood to full up position.

(2)Disconnect the under hood lamp wire connector.

(3)Mark all bolt and hinge attachment locations with a grease pencil or other suitable device to provide reference marks for installation. When install-

ing hood, align all marks and secure bolts. The hood should be aligned to 4 mm (0.160 in.) gap to the front fenders and flush across the top surfaces along fenders.

(4)Remove the top hood to hinge attaching bolts and loosen the bottom bolts until they can be removed by hand.

(5)With assistance of a helper at the opposite side of the vehicle to support the hood, remove the bottom hood to hinge attaching bolts. Separate the hood from the vehicle.

HOOD INSTALLATION

Reverse the preceding operation.

Fig. 2 Hood AssemblyÐTypical

HOOD HINGE REMOVAL (FIG. 3)

(1)Support hood on the side that requires hinge replacement.

(2)Mark all bolt and hinge attachment locations with a grease pencil or other suitable device to provide reference marks for installation. When installing hood hinge, align all marks and secure bolts. The hood should be aligned to 4 mm (0.160 in.) gap to the front fenders and flush across the top surfaces along fenders. Shims can be added or removed under hood hinge to achieve proper hood height.

(3)Remove hood to hinge attaching bolts.

(4)Remove hood hinge to front fender attaching bolts and separate hinge from vehicle.

HOOD HINGE INSTALLATION

Reverse the preceding operation. If necessary, paint new hinge before installation.

Fig. 3 Hood Hinge Assembly

HOOD LATCH AND RELEASE CABLE

HOOD LATCH REMOVAL (FIG. 4)

(1)Raise hood top the full up position.

(2)Remove hood latch attaching bolts holding latch to radiator closure panel and separate from vehicle.

(3)Pry release cable casing attachment from slot receiver on latch, disengage cable end from latch arm hook.

HOOD LATCH INSTALLATION

Reverse the preceding operation.

HOOD LATCH RELEASE CABLE REMOVAL (FIG. 5)

(1)Raise hood to the full up position.

(2)Remove push-in fasteners holding hood latch cover to radiator closure panel and separate cover from vehicle.

(3)Disconnect hood release cable casing and cable end from hood latch assembly. Refer to Hood Latch Removal procedure in this section.

(4)Remove hood latch release cable handle attaching bolts from under left lower edge of instrument panel.

(5)Disengage release cable rubber grommet from engine compartment dash panel behind instrument panel.

(6)Rout cable assembly through engine compartment around battery, under fender lip, under relay bank, and under wiring harnesses, toward dash panel. Push cable through access hole in dash panel under the brake master cylinder, into passenger compartment.

Ä

Fig. 4 Hood LatchÐTypical

HOOD LATCH RELEASE CABLE INSTALLATION

Reverse the preceding operation.

Fig. 5 Hood Latch Release CableÐTypical

FRONT END SPLASH SHIELDS

FRONT WHEELHOUSE SPLASH SHIELD REMOVAL (FIG. 6)

(1)Hoist vehicle and support on suitable safety stands.

(2)Remove front wheel assembly.

(3)Remove push-in fasteners holding front wheelhouse splash shield to fender opening lip and inner wheelhouse area.

(4)Separate wheelhouse splash shield from vehicle.

AP-BODY 23 - 93

FRONT WHEELHOUSE SPLASH SHIELD INSTALLATION

Reverse the preceding operation.

TRANSAXLE SPLASH SHIELD REMOVAL (FIG. 6)

(1)Remove one front wheelhouse splash shield push-in fastener and separate wheelhouse splash shield from transaxle splash shield.

(2)Remove transaxle splash shield attaching bolts and separate transaxle splash shield from vehicle.

TRANSAXLE SPLASH SHIELD INSTALLATION

Reverse the preceding operation.

Fig. 6 Front Wheelhouse and Transaxle Splash

Shields

ENGINE DRIVE BELT SPLASH SHIELD REMOVAL (FIG. 7)

(1)Hoist vehicle and support on suitable safety stands.

(2)Remove bolts holding engine drive belt splash shield to right frame rail.

(3)Separate drive belt splash shield from vehicle.

ENGINE DRIVE BELT SPLASH SHIELD INSTALLATION

Reverse the preceding operation.

FRONT DOOR TRIM PANELÐAP-24/44 Body

DOOR TRIM PANEL REMOVAL (FIG. 8)

(1)Move glass to down position.

(2)Disconnect battery negative cable.

(3)Remove inside latch release handle bezel. Pull outward at forward edge and push bezel rearward.

(4)Remove screw cover from window crank. Remove screw holding crank to regulator and separate crank from door, if equipped.

(5)Remove remote control mirror bezel.

(6)Remove screw covers from arm rest.

(7)Remove screws holding arm rest to door trim. Disconnect power door lock switch wire connector.