Файл: Clavia nord lead 2 v1.0 (eng manual).pdf

Customizing Manual Mode

When you enter Manual mode, the button functions (waveform select, modulation destinations etc.) will be set to some default values, for a basic sound. However, if you would like Manual mode to be different the next time you turn on power, proceed as follows:

1.Enter manual mode.

2.Set all button functions as you want them.

3.Press Store twice.

Storing Programs

Storing is done identically regardless if you are saving an edited Program or if you are saving from Manual mode.

Saving a Program will permanently overwrite an existing Program. Be careful so that you don’t accidentally erase a Program you’d like to keep! However, there is no danger of permanently losing the Factory Programs in RAM locations 01-40, since these are backed up as ROM Performances (see page 108).

1.Press the Store button.

The display flashes.

2.Use the Program Up/Down button to select a Program number.

You can play the now selected Program, in this mode, to decide if you want to replace it or not.

Only Program numbers up to 40 in internal memory Bank can be used for saving!. If you try to save in higher program numbers, nothing will happen!

3.If you change your mind at this point, press the Program Slot you want to return to or hold down Shift and press the Manual (Performance) button to return to Manual Mode.

4.If you decide to go ahead with overwriting the existing Program, press Store again.

The display stops flashing to indicate the Program has been saved.

Copying Programs

Copying Programs between memory slots is just a variation on Storing:

1.Select the Program you want to copy.

2.Press Store.

3.Use the Program Up/Down button to specify the memory location you want to copy the program to.

4.Press Store again.

Using PCMCIA Cards

You can use a standard PCMCIA computer memory card in the slot at the back of the instrument. This allows you to save another three Banks for a total of 297 programmable memory slots and 30 programmable Percussion Kit locations, and 100 Performances (which in practice includes an additional 400 Programs). PCMCIA cards are also perfect for “backing up” (making safety copies of important Programs and Performances).

You can purchase Clavia cards at your Nord Lead 2 dealer. These come with sounds for your instrument, but can be used to store your own.

If you purchase the card at a computer retailer you should ask for this: A 64 kilobyte S-RAM-based, bat- tery-backed PCMCIA card. There are cards with larger memory capacity than 64 kByte but using one with the Nord Lead 2 is simply a waste of money.

Formatting of New Cards

For the Nord Lead 2 to be able to use a new PCMCIA card, it has to be formatted. The instrument will do this for you, if you perform the following steps:

1.Check that the card is not write protected.

This is done with a switch located directly on the card.

2.Insert the card.

The display will flash with the letters “Fo”.

3.To format the card, press Store.

Storing Programs On the Card

This is nothing different from storing into the internal memory Bank. When specifying where to store Program, simply select one of the memory slots above “99”, as when selecting Programs from the card (see page 11).

Storing Performances On the Card

This is described on page 35.

Before storing, make sure the card is not write protected. If it is write protected, the display will not stop flashing when you press Store the second time, to indicate the Program hasn’t been stored.

Updating Cards used with the original Nord Lead

If you have a PCMCIA S-RAM card formatted with the first Nord Lead, you need to update the card to be able to properly save settings for the new parameters, and to have the old sounds play back right on the Nord Lead 2. The instrument can do this for you if your card has already been formatted or updated for the Nord Lead software version 2.x. This was the software update for the original Nord Lead, that added several parameters and features. If your card is formatted for the first software version of the Nord Lead, see the section at the bottom of this page.

In the updating process below, Programs 1-11 in Bank 1 on the card will be erased! Therefore, we recommend that you first copy these Programs to other locations on the card, or save them in a sequencer etc, by using System Exclusive data dump. After having updated the card, you can copy the sounds back to locations 1-11 if you like.

The updating is done as follows:

1.Check that the card is not write protected.

2.Insert the card.

The display will flash with the letters “UP”.

3.To update the card, press Store.

If you have a card formatted for the first software version of the Nord Lead: In this case, the updating procedure above will not work properly. It will allow you to use the card with the Nord Lead 2, but the old sounds may sound different, with some parameters set to the wrong values. Therefore, we recommend that you update your card to software version 2.x before updating it for use with Nord Lead 2. To do this, you need to insert the unprotected card into a regular Nord Lead running software version 2.x. When the display flashes with the letters “UP”, press Store. Now the card is updated for software version 2.x, and can be updated to Nord Lead 2 format.

5. Programming Velocity

Sensitivity

The Filter Velocity Function

Press this button to make the Filter Envelope Amount respond to velocity.

The LED indicates that the Velocity function is activated.

VELOCITY

The quickest way to make a Program velocity sensitive, is to activate the Velocity function in the Filter section. This makes the Filter Envelope Amount vary with striking force, to a pre-determined degree. See page 46 for details.

Making Any Parameter Velocity Dependent

You can make any continuous parameter (those controlled with knobs) react to velocity. You can also set the maximum and minimum boundaries for this, yourself.

Setting The Range

1.Set the parameter to the value you want it to deliver when you play with minimum force.

2.Press the Velocity/morph Assign button.

The LED over the button will flash, indicating that the Nord Lead 2 is in “Velocity Learn” mode.

3.Turn the knob to the value you want it to have at maximum striking force.

You can try out different settings for maximum velocity until you find the most suitable. While the Nord Lead 2 is in “Velocity Learn” mode, you can set ranges for as many parameters as you wish.

4.Press the Velocity/Morph button again.