ВУЗ: Не указан
Категория: Не указан
Дисциплина: Не указана
Добавлен: 21.12.2024
Просмотров: 2284
Скачиваний: 2
Ä
(2)Disengage snap-on linkage at rear of air deflector in sun roof opening.
(3)Remove screws holding air deflector to front of sun roof opening.
INSTALLATION
Reverse the preceding operation.
SUN ROOF DRAIN TUBES
REMOVAL (FIG. 42)
(1)Remove head lining as necessary.
(2)Remove A-pillar or B-pillar trim covers as necessary.
(3)Remove cowl panel and sill plate trim as neces-
sary.
(4)Disconnect effected drain tube from nipple at sun roof opening.
(5)Pull drain tube upward to remove from pillar involved.
INSTALLATION
Reverse the preceding operation. Route the tube to avoid kinks or puncture from sharp edges.
AP-BODY 23 - 109
LIFT GATE REMOTE RELEASE CABLE
REMOVAL
(1)Remove interior trim as necessary to gain access to release cables.
(2)Remove left front door scuff plate.
(3)Remove screw holding trim cover to release cable handle and separate cover from handle.
(4)Remove screw holding release handle to door
sill.
(5)Pry open retainer tab holding cable core end in handle pivot. Pry cable case end from handle.
(6)Remove trunk lining as necessary to gain access to the release cable.
(7)Disconnect cable end from latch.
(8)Separate cable from vehicle.
INSTALLATION
Reverse the preceding operation.
REAR WINDOW GLASS
REMOVAL (FIG. 43)
(1)Raise lift gate to up position.
(2)Remove screws holding outward edges to rear window moulding to lift gate frame.
(3)Position protective card board covers along the top of the quarter panels to protect painted surfaces.
Fig. 42 Sun Roof
23 - 110 AP-BODY
(4)Support lift gate in the up position and remove bolts holding lift gate hinge closed. Lower lift gate to opening weatherstrip.
(5)Remove screws holding top of rear window moulding to lift gate frame. Separate moulding from lift gate.
(6)Pull lower rear window moulding from under
glass.
(7)Cut urethane bonding from around rear window. Refer to Windshield section of this group.
INSTALLATION
Prepare the lift gate fence and rear window as described in the Windshield Installation section of this group. Reverse the removal operation.
Fig. 43 Rear Window Glass
Ä
LIFT GATE LUGGAGE RACK
REMOVAL (FIG. 44)
(1)Remove screws holding cross bar to outboard skid strips.
(2)Pry rubber inserts from skid strips.
(3)Remove screws holding skid strips to lift gate.
INSTALLATION
Reverse the preceding operation
Fig. 44 Lift Gate Luggage Rack
Ä |
AP/27 CONVERTIBLE |
23 - 111 |
|||
AP/27-VEHICLE CONVERTIBLE BODY COMPONENT SERVICE |
|||||
INDEX |
|||||
page |
page |
||||
A-Pillar and Windshield Header Weatherstrip |
. . . . 111 |
Rear Seat Belt Retractor . . . . . . . . . . . . . |
. . . . . 123 |
||
Convertible Top Adjustments . . . . . . . . . . . |
. . . . . 125 |
Rear Tensioner Plate . . . . . . . . . . . . . . . . . |
. . . . 126 |
||
Convertible Top Header . . . . . . . . . . . . . . |
. . . . . 112 |
Rear Window . . . . . . . . . . . . . . . . . . . . . . . |
. . . . 117 |
||
Convertible Top Latch Hooks . . . . . . . . . . . |
. . . . 126 |
Roof Linkage . . . . . . . . . . . . . . . . . . . . . . . |
. . . . 115 |
||
Door Glass Alignment . . . . . . . . . . . . . . . . . |
. . . . 125 |
Roof Rail Weatherstrip . . . . . . . . . . . . . . . . |
. . . . 112 |
||
Door Glass Rear Channel . . . . . . . . . . . . . . |
. . . . 121 |
Roof Rail Weatherstrip Retainer . . . . . . . . . |
. . . . 126 |
||
Door Striker Guide . . . . . . . . . . . . . . . . . . . |
. . . . 122 |
Second Roof Bow and Linkage . . . . . . . . . . |
. . . . 113 |
||
Forward Roof Rail . . . . . . . . . . . . . . . . . . . |
. . . . 115 |
Sling-Well . . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . . 119 |
||
Fourth Roof Bow and Slat . . . . . . . . . . . . . . |
. . . . 114 |
Stationary Quarter Glass and Weatherstrip |
. . . . . 116 |
||
Fourth Roof Bow Slat . . . . . . . . . . . . . . . . . |
. . . . 126 |
Third Roof Bow . . . . . . . . . . . . . . . . . . . . . |
. . . . 114 |
||
Front Door Belt Moulding and Weatherstrip |
. . . . . 121 |
Top Cover . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . . 118 |
||
Front Door Glass . . . . . . . . . . . . . . . . . . . . |
. . . . 119 |
Top Frame . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . . 119 |
||
Front Door Stationary Glass and Division |
Top Header Trim Cover . . . . . . . . . . . . . . . |
. . . . 112 |
|||
Channel . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . . 120 |
Top Latch . . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . . 112 |
||
Front Door Stationary Glass Channel |
Top Lift Assist Cylinder . . . . . . . . . . . . . . . . |
. . . . 116 |
|||
Weatherstrip . . . . . . . . . . . . . . . . . . . . . . |
. . . . 120 |
Top Stack Down-Stop . . . . . . . . . . . . . . . . . |
. . . . 126 |
||
Front Door Striker Guide Socket . . . . . . . . . |
. . . . 121 |
Top Stack Up-Stop . . . . . . . . . . . . . . . . . . . |
. . . . 126 |
||
Front Seat Belt Retractor . . . . . . . . . . . . . . |
. . . . 122 |
Trunk Hinge Lid . . . . . . . . . . . . . . . . . . . . . |
. . . . 125 |
||
General Information . . . . . . . . . . . . . . . . . . |
. . . . 111 |
Trunk Lid . . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . . 124 |
||
Quarter Glass and Roller Bracket . . . . . . . . |
. . . . 126 |
Trunk Lid Applique . . . . . . . . . . . . . . . . . . . |
. . . . 124 |
||
Quarter Panel Belt Moulding . . . . . . . . . . . . |
. . . . 123 |
Trunk Lid Lining . . . . . . . . . . . . . . . . . . . . . |
. . . . 124 |
||
Quarter Trim Panel . . . . . . . . . . . . . . . . . . . |
. . . . 122 |
Trunk Opening Weatherstrip . . . . . . . . . . . . |
. . . . 124 |
||
Rear Roof Rail . . . . . . . . . . . . . . . . . . . . . . |
. . . . 115 |
Windshield Header Lining . . . . . . . . . . . . . . |
. . . . 111 |
||
Rear Seat Back . . . . . . . . . . . . . . . . . . . . . |
. . . . 122 |
Windshield Header Moulding . . . . . . . . . . . . |
. . . . 111 |
||
GENERAL INFORMATION
This section will cover components that are unique to the AP-vehicle convertible. All components that are common to the AP-vehicle two door hardtop are covered in the AP-Vehicle Body Components section.
WINDSHIELD HEADER MOULDING
REMOVAL (FIG. 1)
(1)Remove windshield header lining.
(2)Remove nuts holding moulding to windshield header.
(3)Separate windshield header moulding from ve-
hicle.
INSTALLATION
Apply sealing putty around mounting studs on back of moulding and reverse the removal operation.
WINDSHIELD HEADER LINING
REMOVAL (FIG. 1)
(1)Remove sun visors and inner sun visor hanger
clips.
(2)Remove upper A-pillar trim covers.
(3)Remove dome lamp.
(4)Separate header lining from vehicle.
INSTALLATION
Reverse the preceding operation.
Fig. 1 Windshield Header Moulding
A-PILLAR AND WINDSHIELD HEADER WEATHERSTRIP
REMOVAL (FIG. 2)
(1)Remove upper and lower A-pillar trim covers.
(2)Remove header lining and moulding.
(3)Pull A-pillar door opening weatherstrip from pinch flange.
(4)Pull drip rail weatherstrip from drip rail next to windshield.
23 - 112 AP/27 CONVERTIBLE
(5) Pull windshield header weatherstrip from retaining channel and separate weatherstrip from vehicle.
INSTALLATION
(1)Apply a bead of Mopar, Glass Adhesive and Sealer to back of windshield header weatherstrip.
(2)Apply a strip of double sided adhesive tape to windshield header rearward of the header moulding stud holes.
(3)Reverse the removal operation.
Fig. 2 A-pillar and Windshield Header Weatherstrip
ROOF RAIL WEATHERSTRIP
REMOVAL (FIG. 3)
(1)Remove screw holding front of roof rail weatherstrip to convertible top header.
(2)Pull weatherstrip from retaining channel above door opening.
INSTALLATION
Reverse the preceding operation.
Fig. 3 Roof Rail Weatherstrip
Ä
TOP HEADER TRIM COVER
REMOVAL (FIG. 4)
(1)Lower top.
(2)Remove screws holding header trim to top header.
CAUTION: The screws on the rearward edge have caps over the pointed ends to protect top operator from injury.
(3) Separate trim from header.
INSTALLATION
Reverse the preceding operation.
Fig. 4 Top Header Trim
TOP LATCH
REMOVAL (FIG. 5)
(1)Lower top.
(2)Remove E-ring and clevis pin and separate latch hook from top header.
(3)Remove latch pivot bolts and separate latch from top header.
INSTALLATION
Reverse the preceding operation.
CONVERTIBLE TOP HEADER
REMOVAL
(1)Lower convertible top and remove top header trim cover.
(2)Remove screws holding forward top cover retaining strip to top header and separate strip from top.
(3)Using a heat gun to soften the adhesive, separate the top cover from the top header (Fig. 6).
(4)Peel top cover back over forward edge of header to gain access to stay pad and retention cable attachment.