Файл: 92FWD_23.pdf

(2)Remove shoulder harness turning loop cover. Remove bolt holding turning loop to quarter panel.

(3)Remove rear seat cushion, back, and rear bol-

ster.

(4)Remove screws holding rear header moulding to roof as necessary to clear quarter removal path.

(5)Remove screws holding upper quarter trim panel to quarter panel.

(6)Disengage hook and loop fastener holding trim to quarter panel.

(7)Pull trim panel forward and separate from ve-

hicle.

INSTALLATION

Reverse the preceding operation.

FRONT SEAT BELTSÐAP-44 BODY

FRONT SHOULDER HARNESS/LAP BELT REMOVAL (FIG. 32)

(1)Remove B-pillar trim panel.

(2)Remove bolt holding seat belt retractor to B-pillar.

(3)Separate retractor from vehicle.

FRONT SHOULDER HARNESS/LAP BELT INSTALLATION

Reverse the preceding operation.

FRONT INBOARD BUCKLE REMOVAL (FIG. 32)

(1)Remove bolt holding inboard buckle to floor.

(2)Disconnect seat belt sensor wire connector.

(3)Separate buckle assembly from vehicle.

FRONT INBOARD BUCKLE INSTALLATION

Reverse the preceding operation.

FRONT SEAT BELTSÐAP-24 BODY

FRONT SHOULDER HARNESS/LAP BELT REMOVAL (FIG. 33)

(1)Remove quarter trim panel as necessary.

(2)Remove bolt holding seat belt retractor quarter panel.

(3)Remove bolt holding front lap belt anchor to

floor.

(4)Separate retractor from vehicle.

FRONT SHOULDER HARNESS/LAP BELT INSTALLATION

Reverse the preceding operation.

FRONT INBOARD BUCKLE REMOVAL (FIG. 33)

(1)Remove bolt holding inboard buckle to floor.

(2)Disconnect seat belt sensor wire connector.

(3)Separate buckle assembly from vehicle.

FRONT INBOARD BUCKLE INSTALLATION

Reverse the preceding operation.

Fig. 32 Front Seat BeltsÐAP-44 Body

Fig. 33 Front Seat BeltsÐAP-24 Body

REA R SEAT BELTS

REAR SHOULDER HARNESS/LAP BELT REMOVAL (FIG. 34)

(1) Remove rear shoulder harness turning loop

cover. Remove bolt holding turning loop to roof panel.

(2)Remove quarter trim panel, lower panel on AP-

44.

(3)Remove bolt holding lap belt to floor at wheelhouse kickup.

(4)Remove bolt holding seat belt retractor to quarter panel.

REAR SHOULDER HARNESS/LAP BELT INSTALLATION

Reverse the preceding operation.

REAR INBOARD BUCKLE/CENTER OCCUPANT BELTS REMOVAL (FIG. 34)

(1)Remove rear seat cushion.

(2)Remove bolt holding inboard buckle/center occupant belt to floor.

(3)Separate buckle/belt assembly from vehicle.

REAR INBOARD BUCKLE/CENTER OCCUPANT BELT INSTALLATION

Reverse the preceding operation.

Fig. 34 Rear Seat BeltsÐTypical

FRONT SEATS

REMOVAL (FIG. 35 OR 36)

(1)Position seat full forward.

(2)Remove screws holding rear track riser covers and separate covers from tracks.

(3)On power seat track, remove outboard track

cover.

(4)Remove nuts holding seat track to floor.

(5)Position seat full rearward.

(6)On power seat track, remove door sill scuff plate and disconnect wire connector.

(7)Remove bolts holding seat track to cross mem-

ber.

(8)Remove seat from vehicle.

INSTALLATION

Reverse the preceding operation.

Fig. 35 Manual Front Seat

Fig. 36 Power Front Seat

REAR SEATS

REAR SEAT CUSHION REMOVAL

(1)Remove bolts holding cushion to floor.

(2)Push center occupant seat belts through openings in cushion.

(3)Remove cushion from vehicle.

REAR SEAT CUSHION INSTALLATION

Reverse the preceding operation.

REAR SEAT BACK REMOVAL (FIG. 37)

(1)Hinge seat back forward and disengage push-in fasteners holding carpet backing to trunk floor.

(2)Remove bolts holding outboard hinge pivot bracket to seat back.

(3)Pull seat back outward to disengage inboard pivot and separate from vehicle.

REAR SEAT BACK INSTALLATION

Reverse the preceding operation.

SEAT BACK BOLSTER CUSHION REMOVAL (FIG. 37)

(1)Remove rear seat cushion and back as neces-

sary.

(2)Remove bolts holding outboard seat back bolster to quarter panel.

(3)Lift bolster upward to disengage hook retainer on back of bolster and separate from vehicle.

SEAT BACK BOLSTER CUSHION INSTALLATION

Reverse the preceding operation

Fig. 37 Rear Seat Back and Bolster

FRONT CENTER CONSOLE

REMOVAL (FIG. 38)

(1)Position front seats full forward.

(2)Remove gear selector knob and PRNDL on vehicles with automatic transaxle. Remove illumination lamp socket and position socket out of the way.

(3)Lift gear shift boot adapter from console and push adapter through opening in console on vehicles with manual transaxle.

(4)Remove bolts holding arm rest riser to floor bracket.

(5)Separate rear console from floor and remove from vehicle.

(6)Position front seats full rearward.

(7)Remove radio bezel from instrument panel. Refer to Group 8E, Instrument Panel. Remove screws holding console to instrument panel.

(8)Remove screws holding forward console to lower instrument panel rail.

(9)Remove screws holding forward console to forward brace.

(10)Separate forward console from vehicle.

INSTALLATION

Reverse the preceding operation. Verify PRNDL adjustment before returning vehicle to use.

Fig. 38 Front Center Console

FLOOR CARPET

REMOVAL (FIG. 39)

(1)Remove cowl trim panels and scuff plates.

(2)Remove front seats and inboard seat belts.

(3)Remove center arm rest and front console.

(4)Remove outboard seat belt lower attaching

bolts.

(5)Remove rear seat cushion.

(6)Pull carpet from under B-pillar trim covers.

(7)Fold carpet and remove through front door opening.

INSTALLATION

Reverse the preceding operation.

OVERHEAD CONSOLE

REMOVAL (FIG. 40)

(1)Remove screws holding overhead console to reinforcement bracket.

(2)Slide overhead console rearward to separate reinforcement bracket retainer tab from console.

(3)Lower console from roof and disconnect wire connectors.

Fig. 39 Floor Carpet and SilencersÐTypical

INSTALLATION

Reverse The preceding operation.

Fig. 40 Overhead ConsoleÐTypical

HEAD LINING

REMOVAL (FIG. 41)

(1)Disconnect battery negative cable.

(2)Pull dome lamp downward to disengage from retaining ring in head lining. Separate lens from lamp body and remove bulb. Separate bulb holder from lamp body. Remove attaching screw holding retaining ring to roof bow.

(3)Remove screws holding coat hooks to roof above rear doors.

(4)Remove roof rail and A-pillar mouldings.

(5)Remove screws holding sun visors to roof header and disconnect wire connector, if equipped. Remove inboard sun visor hangers.

(6)Remove overhead console, if equipped.

(7)Pull front reading lamp downward to disengage from retaining ring in head lining and disconnect wire connector. Remove screws holding retaining ring to roof header.

(8)Remove pinch welt holding headlining to sun roof opening, if equipped.

(9)Remove inside rear view mirror from windshield bracket if necessary.

(10)Disengage hook and loop fasteners holding head lining to roof above rear window and slide head lining forward about 25 mm (1 in.).

(11)Shift the front of head lining to one side to pull head lining from behind B-pillar trim. Pull head lining from behind other B-pillar trim.

(12)Allow front of head lining to drop downward. Slide head lining forward from behind quarter panel trim.

(13)Remove head lining from vehicle.

INSTALLATION

Reverse the preceding operation.

Fig. 41 Head LiningÐTypical

SUN ROOF WEATHERSTRIP

REMOVAL (FIG. 42)

(1)Remove sun roof sunshade and glass. Refer to Owner's Manual for instructions.

(2)Pull weatherstrip from pinch flange around sun roof opening.

INSTALLATION

Reverse the preceding operation.

SUN ROOF AIR DEFLECTOR

REMOVAL (FIG. 42)

(1) Remove sun roof sunshade and glass. Refer to Owner's Manual for instructions.