ВУЗ: Не указан
Категория: Не указан
Дисциплина: Не указана
Добавлен: 21.12.2024
Просмотров: 2300
Скачиваний: 2
Ä |
AY-BODY |
23 - 127 |
|||
AY-VEHICLE BODY COMPONENT SERVICE |
|||||
INDEX |
|||||
page |
page |
||||
A-Pillar and Roof Rail Mouldings . . . . . . . . . . . . |
. 137 |
Quarter Trim Panel . . . . . . . . . . . . . . . . . . . |
. . . . 137 |
||
B-Pillar Trim Panel . . . . . . . . . . . . . . . . . . . . . . . |
137 |
Rear Deck Filler Panel . . . . . . . . . . . . . . . . . |
. . . 140 |
||
Body Mouldings . . . . . . . . . . . . . . . . . . . . . . . . . |
140 |
Rear Door and Hinge . . . . . . . . . . . . . . . . . . |
. . . 134 |
||
Cowl Panel Trim and Scuff Plates . . . . . . . . . . . . |
137 |
Rear Door Fixed Glass Outer CoverÐ |
|||
Door Frame Trim Moulding . . . . . . . . . . . . . . . . . |
131 |
AY-S Body . . . . . . . . . . . . . . . . . . . . . . . . |
. . . 135 |
||
Front Door and Hinge . . . . . . . . . . . . . . . . . . . . . |
131 |
Rear Door Fixed Window Module . . . . . . . . . |
. . . 136 |
||
Front Door Glass . . . . . . . . . . . . . . . . . . . . . . . . |
133 |
Rear Door Frame Trim Moulding . . . . . . . . . . |
. . . 133 |
||
Front Door Latch . . . . . . . . . . . . . . . . . . . . . . . . |
132 |
Rear Door Glass . . . . . . . . . . . . . . . . . . . . . |
. . . 135 |
||
Front Door Silencer and Water Shield . . . . . . . . . |
131 |
Rear Door Glass Lift Plate and Guide Bar . . . |
. . . 135 |
||
Front Door Trim Panel . . . . . . . . . . . . . . . . . . . . |
130 |
Rear Door Latch . . . . . . . . . . . . . . . . . . . . . |
. . . 134 |
||
Front Door Window Regulator . . . . . . . . . . . . . . . |
132 |
Rear Door Outer CoverÐAY-P Body . . . . . . . |
. . . 135 |
||
Front End Splash Shields . . . . . . . . . . . . . . . . . . |
130 |
Rear Door Outside Handle . . . . . . . . . . . . . . |
. . . 134 |
||
Front Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . |
138 |
Rear Door Silencer and Water Shield . . . . . . |
. . . 134 |
||
Front Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
139 |
Rear Door Trim Panel . . . . . . . . . . . . . . . . . |
. . . 133 |
||
Grille AY/P Body . . . . . . . . . . . . . . . . . . . . . . . . . |
127 |
Rear Door Window Regulator . . . . . . . . . . . . |
. . . 135 |
||
Grille AY/S Body . . . . . . . . . . . . . . . . . . . . . . . . |
127 |
Rear Seat Belts . . . . . . . . . . . . . . . . . . . . . . |
. . . 138 |
||
Grille Opening Panel AY/P Body . . . . . . . . . . . . . |
128 |
Rear Seats . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . 140 |
||
Grille Opening Panel AY/S Body . . . . . . . . . . . . . |
128 |
Rear Shelf Trim Panel . . . . . . . . . . . . . . . . . |
. . . 138 |
||
Head Lining . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
136 |
Rear Window Glass . . . . . . . . . . . . . . . . . . . |
. . . 141 |
||
Hood and Hinges . . . . . . . . . . . . . . . . . . . . . . . . |
128 |
Side View Mirror Trim Cover . . . . . . . . . . . . . |
. . . 131 |
||
Hood Latch and Release Cable . . . . . . . . . . . . . |
129 |
Trunk Lid . . . . . . . . . . . . . . . . . . . . . . . . . . . |
. . . 141 |
||
Hood Ornament AY/P-S . . . . . . . . . . . . . . . . . . . |
128 |
Trunk Lid Hinge . . . . . . . . . . . . . . . . . . . . . . |
. . . 141 |
||
Outside Door Handle . . . . . . . . . . . . . . . . . . . . . |
132 |
Trunk Lid Torsion Bar . . . . . . . . . . . . . . . . . . |
. . . 142 |
||
Overhead Console . . . . . . . . . . . . . . . . . . . . . . . |
136 |
Vinyl Roof Bonnet . . . . . . . . . . . . . . . . . . . . |
. . . 140 |
||
GRILLE AY/P BODY
REMOVAL (FIG. 1)
(1)Remove screws holding grille to opening panel.
(2)Push top of grille downward and pull forward.
(3)Separate grille from vehicle.
INSTALLATION
Reverse the preceding operation.
GRILLE AY/S BODY
REMOVAL (FIG. 2)
(1)Loosen hidden screws holding grille to grille opening panel at corners of grille. The screws are captured in a clearance hole covered by a bracket behind the grille.
(2)Pull grille forward from grille opening panel.
INSTALLATION
Reverse the preceding operation.
Fig. 1 GrilleÐAY/P Body
Fig. 2 GrilleÐAY/S Body
23 - 128 AY-BODY
HOOD ORNAMENT AY/P-S
REMOVAL (FIG. 2)
(1)Remove grille.
(2)Locate hood ornament spring under grille opening panel header.
(3)Compress hood ornament spring enough to clear hooks on end of retaining wire.
(4)Squeeze retainer wire hooks together and push hooks inside spring.
(5)Rotate spring counterclockwise to separate spring from retainer.
(6)Separate hood ornament from grille opening panel.
INSTALLATION
Reverse the preceding operation.
GRILLE OPENING PANEL AY/P BODY
For service procedures for headlamp related components refer to Group 8L, Lamps.
REMOVAL (FIG. 3)
(1)Remove front bumper and grille.
(2)Remove front end splash shields as necessary to gain access to behind fenders.
(3)Remove nuts holding GOP mouldings to front fenders.
(4)Remove nuts holding grille opening panel to front fenders.
(6)Disconnect concealed headlamp motor wire connector.
(7)Disconnect all lamp wire connectors.
(8)Remove bolts holding grille opening panel to radiator closure panel and center brace.
(9)Separate grille opening panel from vehicle.
INSTALLATION
Reverse the preceding operation.
Fig. 3 Grille Opening PanelÐAY/P Body
Ä
GRILLE OPENING PANEL AY/S BODY
For service procedures for headlamp related components refer to Group 8L, Lamps.
REMOVAL (FIG. 4)
(1)Remove front bumper and grille.
(2)Remove front end splash shields as necessary to gain access to behind fenders.
(3)Remove nuts holding mouldings to front fend-
ers.
(4)Remove bolts holding mouldings to bottom of grille opening panel and separate mouldings from vehicle.
(5)Remove nuts holding grille opening panel to front fenders.
(6)Disconnect concealed headlamp motor wire connector.
(7)Disconnect headlamp wire connectors.
(8)Remove bolts holding grille opening panel to radiator closure panel mount brackets and center brace.
(9)Separate grille opening panel from vehicle.
INSTALLATION
Reverse the preceding operation.
Fig. 4 Grille Opening PanelÐAY/S Body
HOOD AND HINGES
HOOD REMOVAL (FIG. 5)
(1)Raise hood to full up position.
(2)Lift front edge of cowl cover on the right side of the windshield washer bottle and disconnect the under hood lamp wire connector.
(3)Mark all bolt and hinge attachment locations with a grease pencil or other suitable device to provide reference marks for installation. When installing hood, align all marks and secure bolts. The hood should be aligned to 4 mm (0.160 in.) gap to the front fenders and flush across the top surfaces along fenders.
Ä |
AY-BODY 23 - 129 |
|
(4)Remove the top hood to hinge bolts and loosen the bottom bolts until they can be removed by hand.
(5)With assistance of a helper at the opposite side of the vehicle to support the hood, remove the bottom hood to hinge bolts. Separate the hood from the vehicle.
HOOD INSTALLATION
Reverse the preceding operation.
Fig. 5 Hood
HOOD HINGE REMOVAL (FIG. 6)
(1)Support hood on the side that requires hinge replacement.
(2)Mark all bolt and hinge attachment locations with a grease pencil or other suitable device to provide reference marks for installation. When installing hood hinge, align all marks and secure bolts. The hood should be aligned to 4 mm (0.160 in.) gap to the front fenders and flush across the top surfaces along fenders. Shims can be added or removed under hood hinge to achieve proper hood height.
(3)Remove hood to hinge attaching bolts.
(4)Remove hood hinge to front fender attaching bolts and separate hinge from vehicle.
HOOD HINGE INSTALLATION
Reverse the preceding operation. If necessary, paint new hinge before installation.
HOOD LATCH AND RELEASE CABLE
HOOD LATCH REMOVAL (FIG. 7)
(1) Raise hood top the full up position.
Fig. 6 Hood HingeÐTypical
(2)Remove hood latch attaching bolts holding latch to radiator closure panel and separate from vehicle.
(3)Pry release cable casing attachment from slot receiver on latch, disengage cable end from latch arm hook.
HOOD LATCH INSTALLATION
Reverse the preceding operation.
Fig. 7 Hood Latch AssemblyÐTypical