Файл: 92FWD_23.pdf

Ä

REAR DOOR GLASS

REMOVAL (FIG. 19)

(1)Remove rear door trim panel.

(2)Remove silencer pad and water shield.

(3)Remove door frame trim moulding.

(4)Remove screws holding lift plate to door glass.

(5)Loosen glass slam bumpers.

(6)Lift glass upward through opening at top of

door.

INSTALLATION

Reverse the preceding operation.

Fig. 19 Rear Door

REAR DOOR WINDOW REGULATOR

REMOVAL

(1)Remove rear door trim panel.

(2)Remove silencer pad and water shield.

(3)Remove bolts holding regulator to inner door panel.

(4)Slide regulator lift arm roller from lift plate channel.

(5)Separate regulator from door.

INSTALLATION

Reverse the preceding operation.

REAR DOOR GLASS LIFT PLATE AND GUIDE BAR

REMOVAL

(1) Remove rear door glass.

AC-BODY 23 - 45

(2)Remove bolts holding upper guide bar mount bracket to inner door panel.

(3)Remove nut holding guide bar to lower door bottom frame.

(4)Slide lift plate channel from regulator roller.

(5)Separate guide bar from door.

INSTALLATION

Reverse the preceding operation.

OVERHEAD CONSOLE

REMOVAL (FIG. 20)

(1)Remove screws holding overhead console to reinforcement bracket.

(2)Slide overhead console rearward to separate reinforcement bracket retainer tab from console.

(3)Lower console from roof and disconnect wire connectors.

INSTALLATION

Reverse The preceding operation.

Fig. 20 Overhead Console

HEAD LINING

REMOVAL (FIG. 21)

(1)Disconnect battery negative cable.

(2)Pull dome lamp downward to disengage from retaining ring in head lining. Separate lens from lamp body and remove bulb. Separate bulb holder from lamp body. Remove attaching screw holding retaining ring to roof bow.

(3)Remove screws holding coat hooks to roof above rear doors.

(4)Remove roof rail and A-pillar mouldings.

(5)Remove screws holding sun visors to roof header and disconnect wire connector, if equipped. Remove inboard sun visor hangers.

(6)Remove overhead console, if equipped.

23 - 46 AC-BODY

(7)Pull front reading lamp downward to disengage from retaining ring in head lining and disconnect wire connector. Remove screws holding retaining ring to roof header.

(8)Remove pinch welt holding headlining to sun roof opening, if equipped.

(9)Remove inside rear view mirror from windshield bracket, if necessary.

(10)Disengage hook and loop fasteners holding head lining to roof above rear window and slide head lining forward about 25 mm (1 in.).

(11)Shift the front of head lining to one side to pull head lining from behind B-pillar trim. Pull head lining from behind other B-pillar trim.

(12)Allow front of head lining to drop downward. Slide head lining forward from behind quarter panel trim.

(13)Remove head lining from vehicle.

INSTALLATION

Reverse the preceding operation.

Fig. 21 Head LiningÐTypical

COWL PANEL TRIM AND SCUFF PLATES

COWL PANEL AND DOOR OPENING SCUFF PLATE REMOVAL (FIG. 22)

(1)Open front door.

(2)Remove screw holding trim panel to cowl forward of the front door opening.

(3)Remove screws holding scuff plate to door sill.

(4)Separate cowl panel trim and scuff plate from vehicle.

Ä

COWL PANEL AND DOOR OPENING SCUFF PLATE INSTALLATION

Reverse the preceding operation.

REAR DOOR OPENING SCUFF PLATE REMOVAL (FIG. 22)

(1)Open rear door.

(2)Remove screws holding scuff plate to door sill.

(3)Separate scuff plate from vehicle.

REAR DOOR OPENING SCUFF PLATE INSTALLATION

Reverse the preceding operation.

A-PILLAR AND ROOF RAIL MOULDINGS

A-PILLAR MOULDING REMOVAL (FIG. 22)

(1)Open front door.

(2)Disengage clips holding A-pillar moulding to roof rail above door opening.

(3)Slide A-pillar moulding upward and pull rearward to separate moulding from A-pillar.

A-PILLAR MOULDING INSTALLATION

Reverse the preceding operation.

REAR DOOR ROOF RAIL MOULDING REMOVAL (FIG. 22)

(1)Open rear door.

(2)Disengage clips holding roof rail moulding to roof rail above rear door opening.

(3)Separate moulding from vehicle.

REAR DOOR ROOF RAIL MOULDING INSTALLATION

Reverse the preceding operation.

B-PILLAR TRIM PANEL

REMOVAL (FIG. 22)

(1)Remove roof rail mouldings and scuff plates as necessary.

(2)Remove shoulder harness turning loop cover. Remove bolt holding turning loop to B-pillar.

(3)Remove bolt holding seat belt to floor below B-pillar.

(4)Remove upper B-pillar trim.

(5)Remove lower B-pillar trim.

INSTALLATION

Reverse the preceding operation.

QUARTER TRIM PANEL

REMOVAL (FIG. 22)

(1) Remove rear roof rail mouldings and scuff plates as necessary.