Файл: 92FWD_23.pdf

Ä

(2)Remove rear shoulder harness turning loop cover. Remove bolt holding turning loop to quarter panel.

(3)Remove rear seat cushion and back.

(4)Remove push-in fastener holding quarter trim to roof rail.

(5)Remove screws holding quarter trim panel to wheelhouse kickup.

(6)Pull trim panel away from C-pillar and separate from vehicle.

INSTALLATION

Reverse the preceding operation.

REAR SHELF TRIM PANEL

REMOVAL (FIG. 22)

(1)Remove one quarter trim panel.

(2)Remove center high mounted stop lamp cover. Refer to Group 8L, Lamps for instructions.

(3)Disengage fasteners holding trim to shelf panel and separate trim from vehicle.

INSTALLATION

Reverse the preceding operation.

FRONT SEAT BELTS

OUTBOARD SHOULDER HARNESS/LAP BELT REMOVAL (FIG. 23)

(1)Remove B-pillar trim panel.

(2)Remove bolt holding seat belt retractor to B-pillar.

(3)Separate retractor from vehicle.

AC-BODY 23 - 47

OUTBOARD SHOULDER HARNESS/LAP BELT INSTALLATION

Reverse the preceding operation.

INBOARD BUCKLE/CENTER OCCUPANT BELTS REMOVAL (FIG. 23)

Vehicles equipped with front bucket seats with center console do not have center occupant belts.

(1)Remove bolt holding inboard buckle/center occupant belt to floor.

(2)Disconnect seat belt sensor wire connector.

(3)Separate buckle/belt assembly from vehicle.

INBOARD BUCKLE/CENTER OCCUPANT BELT INSTALLATION

Reverse the preceding operation.

REAR SEAT BELTS

OUTBOARD SHOULDER HARNESS/LAP BELT REMOVAL (FIG. 24)

(1)Remove quarter trim panel.

(2)Remove bolt holding lap belt to floor at wheelhouse kickup.

(3)Remove bolt holding turning loop to inner quarter panel.

(4)Remove bolt holding seat belt retractor to quarter panel.

OUTBOARD SHOULDER HARNESS/LAP BELT INSTALLATION

Reverse the preceding operation.

23 - 48 AC-BODY

Fig. 23 Front Seat Belts

INBOARD BUCKLE/CENTER OCCUPANT BELTS REMOVAL (FIG. 24)

(1)Remove rear seat cushion.

(2)Remove bolt holding inboard buckle/center occupant belt to floor.

(3)Separate buckle/belt assembly from vehicle.

INBOARD BUCKLE/CENTER OCCUPANT BELT INSTALLATION

Reverse the preceding operation.

Ä

FRONT SEATS

REMOVAL (FIG. 25 OR 26)

(1)Position seat full forward.

(2)Remove screws holding rear track riser covers and separate covers from tracks.

(3)On power seat track, remove outboard track

cover.

(4)Remove inboard seat belt attaching bolt from

floor.

(5)Remove nuts holding seat track to floor.

(6)Position seat full rearward.

(7)Remove door sill scuff plate and disconnect power seat track wire connector.

(8)Remove bolts holding seat track to cross mem-

ber.

(9)Remove seat from vehicle.

INSTALLATION

Reverse the preceding operation.

Fig. 25 Manual Front SeatÐTypical

Fig. 26 Power Front SeatÐTypical

Ä

REAR SEATS

REAR SEAT CUSHION REMOVAL

(1)Remove bolts holding cushion to floor.

(2)Disconnect center occupant seat belts from cushion.

(3)Remove cushion from vehicle.

REAR SEAT CUSHION INSTALLATION

Reverse the preceding operation.

REAR SEAT BACK REMOVAL

(1)Remove rear seat cushion assembly.

(2)Remove bolts holding seat back to rear floor kick-up.

(3)Lift seat back upward to disengage upper hooks from shelf support panel.

(4)Separate seat back from vehicle.

REAR SEAT BACK INSTALLATION

Reverse the preceding operation.

BODY MOULDINGS

STICK-ON BODY SIDE MOULDING REMOVAL AND INSTALLATION

(1)Warm the effected stick-on moulding and body metal to approximately 38°C (100°F) using a suitable heat lamp or heat gun.

(2)Pull stick-on moulding from painted surface.

(3)Remove adhesive tape residue from painted surface of vehicle.

(4)If moulding is to be reused, Remove tape residue from moulding. Clean back of moulding with Mopart, Super Kleen solvent or equivalent. Wipe moulding dry with lint free cloth. Apply new body side moulding (two sided adhesive) tape to back of moulding.

(5)Clean body surface with Super Kleen solvent or equivalent. Wipe surface dry with lint free cloth.

(6)Apply a length of masking tape on the body, parallel to the top edge of the moulding to use as a guide, if necessary.

(7)Remove protective cover from tape on back of moulding. Apply moulding to body below the masking tape guide.

(8)Remove masking tape guide and heat body and moulding, see step one. Firmly press moulding to body surface to assure adhesion.

FRONT WHEEL OPENING MOULDING REMOVAL

(1)Remove screws holding wheel opening moulding to front fender.

(2)Separate moulding from fender.

AC-BODY 23 - 49

FRONT WHEEL OPENING MOULDING INSTALLATION

(1)Position moulding in wheel opening and start top center screw of wheel opening moulding.

(2)Install screws around wheel opening.

REAR WHEEL OPENING MOULDING REMOVAL

(1)Remove screws holding wheel opening moulding to quarter panel.

(2)Separate wheel opening moulding from quarter panel.

REAR WHEEL OPENING MOULDING INSTALLATION

(1)Position moulding in wheel opening and start top center screw of wheel opening moulding.

(2)Install screws around wheel opening.

VINYL ROOF BONNET

REMOVAL (FIG. 27)

(1)Remove quarter panel trim covers.

(2)Remove head lining.

(3)Remove nuts holding transverse roof moulding to roof panel and separate moulding from vehicle.

(4)Remove nuts holding vinyl top bonnet to roof.

(5)Remove rear deck filler panel.

(6)Remove screws holding rear window opening lower valance to body.

(7)Disengage hook and loop fasteners holding vinyl top bonnet to quarter panel.

(8)Pull vinyl top bonnet away from top panel to separate bonnet from anti-flutter sealer holding bonnet to roof.

INSTALLATION

(1)Clean anti-flutter sealer from roof surface and inside of vinyl roof bonnet.

(2)Apply a 20 mm (0.75 in.) bead of anti-flutter sealer across the roof panel at the mid point between the front of the bonnet and rear of roof.

(3)Apply a 20 mm (0.75 in.) by 150 mm (6 in.) bead of anti-flutter sealer down each roof side panel at mid point between the door opening and rear of roof.

(4)Place the bonnet into position on the roof panel and align to proper fit.

(5)Reverse the removal operation.

REAR DECK FILLER PANEL

REMOVAL (FIG. 28)

(1)Raise truck lid to full up position.

(2)Remove screws holding rear deck filler panel to body in the front trunk opening gutter.

(3)Close trunk lid, do not latch.

(4)Lift filler panel upward and separate from ve-

hicle.

Fig. 27 Vinyl Roof BonnetÐTypical

INSTALLATION

Reverse the preceding operation.

Fig. 28 Rear Deck Filler PanelÐTypical

REAR WINDOW GLASS

REMOVAL (FIG. 29)

The rear window moulding often cannot be salvaged after removal operation is completed. Verify moulding availability from the parts supplier before removing moulding.

(1)Remove rear deck filler panel.

(2)Pull rear window moulding from between glass and roof panel.

(3)Remove interior trim as necessary to gain access to rear window defogger wire connector and ground screw, if equipped.

(4) Remove vinyl roof bonnet, if equipped.

WARNING: WEAR EYE AND HAND PROTECTION WHEN HANDLING SAFETY GLASS. PERSONAL INJURY CAN RESULT.

CAUTION: Do not damage body or trim finish when cutting out glass or applying fence primer.

(5)Cut the urethane around the perimeter of the back window glass. Refer to Windshield section of this group for proper procedures.

(6)Separate the rear window from the vehicle.

INSTALLATION

(1)Prepare the work area, window fence, and glass the same way as described in the Windshield section of this group.

(2)Place fence spacers at the locations shown (Fig.

29).

(3)Apply a 10 mm (0.4 in.) bead of urethane around the perimeter of the glass.

(4)Install the glass in the same manner described in the Windshield section of this group.

(5)Install the rear window moulding in the gap between the glass and the roof panel.

(6)Secure moulding and glass in position with suitable tape. Remove tape after urethane has cured.

(7)Connect rear window defogger wiring. Install interior trim and rear deck filler panel.

(8)After urethane has cured, water test rear window to verify repair. Verify rear window defogger operation, see Group 8N, Rear Window Defogger.

TRUNK LID

REMOVAL (FIG. 30)

(1)Raise trunk lid to full up position.

(2)Disconnect the trunk lamp wire connector.

(3)Mark all bolt and hinge attachment locations with a grease pencil or other suitable device to provide reference marks for installation. When installing trunk lid, align all marks and secure bolts. The trunk lid should be aligned to 4 mm (0.160 in.) gap to the quarter panels and flush across the top surfaces along quarter panels.

(4)Remove the top trunk lid to hinge attaching bolts and loosen the bottom bolts until they can be removed by hand.

(5)With assistance of a helper at the opposite side of the vehicle to support the trunk lid, remove the bottom trunk lid to hinge attaching bolts. Separate the trunk lid from the vehicle.

INSTALLATION

Reverse the preceding operation.