Файл: 92FWD_23.pdf

Fig. 12 Front Door Assembly

(4) Remove bolts holding hinge to hinge pillar and separate hinge form vehicle.

FRONT DOOR HINGE INSTALLATION

Reverse the preceding operation. Align door to achieve 6 mm (0.240 in.) gap to all surrounding panels and flush across gaps.

OUTSIDE DOOR HANDLE

REMOVAL (FIG. 13)

(1)Remove door trim panel.

(2)Remove silencer pad and water shield as neces-

sary.

(3)Raise door glass to up position.

(4)Disconnect illuminated entry wire connector from outside door handle assembly, if equipped.

(5)Disconnect latch release linkage from latch assembly.

(6)Disconnect lock cylinder linkage from latch assembly.

(7)Remove nuts holding outside handle bracket to door panel and separate bracket from panel.

(8)Position linkage rods parallel to the back of handle and remove handle assembly from door.

INSTALLATION

Reverse the preceding operation.

FRONT DOOR LATCH

REMOVAL (FIG. 14)

(1)Remove door trim panel.

(2)Remove silencer pad and water shield as neces-

sary.

(3)Disconnect linkage rods from door latch assem-

bly.

(4)Remove screws holding latch door end frame.

(5)Separate latch from door.

Fig. 13 Front Door Handle Assembly

INSTALLATION

Reverse the preceding operation.

Fig. 14 Front Door Latch Assembly

FRONT DOOR WINDOW REGULATOR

REMOVAL (FIG. 15 OR 16)

MANUAL OR ELECTRIC

(1)Remove front door trim panel.

(2)Remove silencer pad and water shield.

(3)Remove side view mirror trim cover and door frame trim moulding.

(4)Remove door glass.

(5)Remove nut holding cable retainer to inner door panel and slip cables from behind retainer.

(6)Disengage push in retainer holding cables to inner door panel above speaker on vehicles with power windows.

(7)Remove bolts holding top of glass lift bar to inner door panel.

(8)Remove nut holding bottom of lift bar to bottom panel of door.

(9)Remove bolts holding window crank regulator to inner door panel on vehicles with manual windows. Remove nuts holding motor and regulator to inner door panel on vehicles with power windows.

(10)Separate window regulator from vehicle.

INSTALLATION

Reverse the preceding operation.

Fig. 15 Front Door Manual Window Regulator

FRONT DOOR GLASS

REMOVAL

(1)Remove front door trim panel.

(2)Remove silencer pad and water shield.

(3)Remove side view mirror trim cover and door frame trim moulding.

(4)Remove front door speaker.

(5)Move glass to the down position and remove glass to lift plate fasteners.

(6)Loosen door glass slam bumpers.

(7)Lift glass upward through opening at top of

door.

INSTALLATION

Reverse the preceding operation.

Fig. 16 Front Door Power Window Regulator

REAR DOOR TRIM PANEL

REMOVAL (FIG. 17)

(1)Disengage retaining clips holding padded insert assembly to door panel.

(2)Remove courtesy lamp lens.

(3)Remove screws holding arm rest to door panel.

(4)Remove screws at forward edge of trim panel.

(5)Remove hidden screws from carpet insert on lower trim panel.

(6)Remove screw and disengage clips holding switch bezel to door trim panel.

(7)Disengage frog-leg fasteners holding trim panel to door and disconnect courtesy lamp wire connector.

INSTALLATION

Reverse the preceding operation.

REAR DOOR FRAME TRIM MOULDING

TRIM MOULDING REMOVAL (FIG. 17)

(1)Remove rear door trim panel.

(2)Disengage trim clips holding trim moulding to door frame.

(3)Separate trim moulding from door frame.

TRIM MOULDING INSTALLATION

Reverse the preceding operation.

REAR DOOR SILENCER AND WATER SHIELD

REAR DOOR WATER SHIELD REMOVAL

(1)Remove door trim panel.

(2)Pull water shield from adhesive around perimeter of door inner panel.

23 - 44 AC-BODY

Fig. 17 Rear Door Trim Panel

REAR DOOR SILENCER AND WATER SHIELD INSTALLATION

Reverse the preceding operation.

REAR DOOR AND HINGE

The rear door hinge is welded to the door and bolted to the B-pillar. The door half of the hinge pivots on a removable hinge pin. The hinge pin is driven in from the bottom on the top hinge and from the top on the bottom hinge. All adjustments to the hinge are performed on the hinge pillar half of the hinge. If the welded half of the hinge must be bent to align door, consult an authorized body repair facility.

REAR DOOR REMOVAL (FIG. 18)

(1)Remove B-pillar trim panel and disconnect all wire connectors leading to door. Push wire harness through access hole in B-pillar into hinge opening.

(2)Support door on a suitable lifting device.

(3)Drive bottom hinge pin upward and remove pin from hinge.

(4)Drive top hinge pin downward and remove pin from hinge.

(5)Separate door from vehicle.

REAR DOOR INSTALLATION

Reverse the preceding operation. The door should not require re-alignment. If door does need alignment, refer to Rear Door Hinge Installation paragraph in this section.

REAR DOOR HINGE REMOVAL (FIG. 18)

(1) To remove upper hinge bolted half, remove B-pillar trim panel. To remove lower hinge bolted half it is not necessary to remove B-pillar trim.

Ä

Fig. 18 Rear Door AssemblyÐTypical

(2)Support rear door on a suitable lifting device.

(3)Drive out hinge pin on the effected hinge.

(4)Remove bolts holding hinge to B-pillar and separate hinge form vehicle.

REAR DOOR HINGE INSTALLATION

Reverse the preceding operation. Align door to achieve 6 mm (0.240 in.) gap to all surrounding panels and flush across gaps.

REAR DOOR OUTSIDE HANDLE

REMOVAL

(1)Remove rear door trim panel.

(2)Remove silencer pad and water shield as neces-

sary.

(3)Disconnect latch release linkage rod from door

latch.

(4)Remove nuts holding handle bracket to inner door panel.

(5)Separate outside door handle from door.

INSTALLATION

Reverse the preceding operation.

REAR DOOR LATCH

REMOVAL

(1)Remove rear door trim panel.

(2)Remove silencer pad and water shield as neces-

sary.

(3)Disconnect linkage rods from door latch.

(4)Remove screws holding latch to door end frame.

(5)Separate latch from rear door.

INSTALLATION

Reverse the preceding operation.