Файл: 92FWD_23.pdf

Ä

FRONT DOOR REMOVAL (FIG. 14)

(1)Remove door trim panel, silencer pad, and water shield.

(2)Disconnect all wire connectors and wire harness hold downs inside door and push wire harness through access hole in front of door into hinge pillar opening.

(3)Open door and support door on a suitable lifting device.

(4)Drive bottom hinge pin upward and remove pin from hinge.

(5)Drive top hinge pin downward and remove pin from hinge.

FRONT DOOR INSTALLATION

Reverse the preceding operation. The door should not require re-alignment. If door does need alignment, refer to Front Door Hinge Installation paragraph in this section.

Fig. 14 Front Door Assembly

FRONT DOOR HINGE REMOVAL (FIG. 14)

(1)Remove front fender wheelhouse splash shield. Refer to Front Wheelhouse Splash Shield Removal paragraph in this section.

(2)Support door on a suitable lifting device.

(3)Drive out hinge pin on the effected hinge.

(4)Remove bolts holding hinge to hinge pillar and separate hinge form vehicle.

FRONT DOOR HINGE INSTALLATION

Reverse the preceding operation. Align door to achieve 6 mm (0.240 in.) gap to all surrounding panels and flush across gaps.

DOOR LATCH

REMOVAL

(1)Remove door trim panel.

(2)Remove silencer and water shield, as necessary.

(3)Raise door glass to up position.

AG-BODY 23 - 57

(4)Disconnect linkage rods from door latch assem-

bly.

(5)Remove screws holding latch top door end frame.

(6)Separate latch from door.

INSTALLATION

Reverse the preceding operation.

MANUAL WINDOW REGULATOR

REMOVAL

(1)Remove door trim panel.

(2)Remove silencer and water shield as necessary.

(3)Raise glass to 25 mm (1 in.) below full up position and support glass lift plate to keep the glass from falling.

(4)Remove bolts holding regulator to inner door panel.

(5)Slide regulator lift arm roller from lift plate channel.

(6)Remove regulator assembly through access hole in door.

INSTALLATION

Reverse the preceding operation.

POWER WINDOW REGULATOR

REMOVAL (FIG. 15)

(1)Remove door trim panel.

(2)Remove silencer and water shield as necessary.

(3)Raise glass to 25 mm (1 in.) below full up position and support glass to keep the glass from falling. Disconnect battery negative cable.

(4)Remove bolts holding regulator to inner door panel.

(5)Remove nuts holding lift plate to glass.

(6)Remove regulator assembly through access hole in door.

INSTALLATION

Reverse the preceding operation.

Fig. 15 Power Window Regulator

23 - 58 AG-BODY

MANUAL WINDOW REGULATOR

REMOVAL (FIG. 16)

(1)Remove door trim panel.

(2)Remove silencer and water shield as necessary.

(3)Raise glass to 25 mm (1 in.) below full up position and support glass to keep the glass from falling.

(4)Remove bolts holding regulator to inner door panel.

(5)Remove nuts holding lift plate to glass.

(6)Remove regulator assembly through access hole in door.

INSTALLATION

Reverse the preceding operation.

Fig. 16 Manual Window Regulator

MANUAL WINDOW LIFT PLATE AND GUIDE

REMOVAL (FIG. 16)

(1)Remove door trim panel, silencer and water shield.

(2)Raise glass enough to align lift plate to large access hole in inner door panel.

(3)Remove nuts holding glass to lift plate.

(4)Separate glass from lift plate and allow glass to rest on bottom of door.

(5)Remove bolt holding guide bar to upper door frame.

(6)Remove bolts holding guide bar top inner door panel.

(7)Slide regulator lift arm roller from lift plate channel.

(8)Remove lift plate and guide bar through large access hole in inner door panel.

INSTALLATION

Reverse the preceding operation.

Ä

DOOR GLASS

REMOVAL (FIG. 17)

(1)Remove door trim panel.

(2)Remove silencer and water shield.

(3)Raise door glass 100 mm (4 in.) from down position.

(4)Disconnect battery negative cable if equipped with power windows.

(5)Loosen bolts holding glass stabilizers and guide hook receiver to top of inner door frame.

(6)Remove nuts holding door glass to lift plate.

(7)Separate glass from lift plate and lift glass upward from opening at top of door.

INSTALLATION

Reverse the preceding operation.

Fig. 17 Door Glass

GLASS RUN WEATHERSTRIP

REMOVAL

(1)Remove door trim panel.

(2)Remove silencer and water shield as necessary.

(3)Remove side view mirror cover.

(4)Pull glass run weatherstrip from door frame channel.

INSTALLATION

Reverse the preceding operation.

OUTSIDE DOOR LATCH RELEASE HANDLE

REMOVAL (FIG. 18)

(1)Remove door trim panel, silencer pad, and water shield.

(2)Raise door glass to full up position.

(3)Disconnect security alarm switch and illuminated entry switch from back of outside front door latch release handle, if equipped. For additional information refer to Group 8Q, Vehicle Theft Security System

(4)Disconnect lock rod and latch release rod from door latch assembly.

(5)Remove nuts holding outside door latch handle to retainer bracket and separate bracket from door.

(6)Swing lock rod upward, parallel to back of latch handle, and separate latch handle from door panel.

INSTALLATION

Reverse the preceding operation.

Fig. 18 Outside Door Latch Release HandleÐTypical

INSIDE LATCH RELEASE HANDLE

REMOVAL

(1)Remove door trim panel.

(2)Remove screw holding handle to inner door panel.

(3)Disconnect linkage rod from back of handle.

(4)Separate handle from door.

INSTALLATION

Reverse the preceding operation.

POWER DOOR LOCK ACTUATOR

REMOVAL (FIG. 19)

(1)Remove door trim panel. Remove silencer and water shield as necessary.

(2)Raise door glass to the up position.

(3)Disconnect battery negative cable.

(4)Disconnect lock actuator linkage rod from door

latch.

(5)Remove bolts holding actuator to inner door panel.

(6)Separate power door lock actuator from door.

INSTALLATION

Reverse the preceding operation.

SIDE VIEW MIRROR

REMOVAL (FIG. 20)

(1)Remove door trim panel.

(2)Disconnect power mirror wire connector.

Fig. 19 Power Door Lock Actuator

(3)Remove covers to gain access to mirror attaching nuts.

(4)Remove nuts holding mirror to door frame.

(5)Separate mirror from door frame.

INSTALLATION

Reverse the preceding operation.

Fig. 20 Side View Mirror

DOOR GLASS OPENING MOULDING

REMOVAL

(1)Remove door trim panel.

(2)Remove door glass.

(3)Remove side view mirror.

(4)Disengage clips holding door glass opening moulding to the door frame (Fig. 21).

(5)Remove screws holding door glass opening moulding and belt weatherstrip to door belt flange (Fig. 22).

(6)Remove the belt weatherstrip.

(7)Remove window opening moulding.

INSTALLATION

Reverse the preceding operation.