Файл: 92FWD_23.pdf

Ä

REAR SEAT BELTS

REAR OUTBOARD SHOULDER HARNESS/LAP BELT REMOVAL (FIG. 27)

(1)Remove lower and upper quarter trim panel.

(2)Remove bolt holding lap belt anchor to floor at wheelhouse kickup.

(3)Remove bolt holding seat belt retractor to quarter panel.

REAR OUTBOARD SHOULDER HARNESS/LAP BELT INSTALLATION

Reverse the preceding operation.

REAR INBOARD BUCKLE REMOVAL (FIG. 27)

(1)Lift seat belt buckle anchor cover to expose bolt.

(2)Remove bolt holding inboard buckle/center occupant belt to seat frame.

(3)Separate buckle from vehicle.

REAR INBOARD BUCKLE INSTALLATION

Reverse the preceding operation.

Fig. 27 Rear Seat Belts

FRONT SEATS

REMOVAL (FIG. 28 OR 29)

(1)Position seat full forward.

(2)Remove screws holding rear track riser covers and separate covers from tracks.

(3)On power seat track, remove outboard track

cover.

(4)Remove nuts holding seat track to floor.

(5)Position seat full rearward.

(6)On power seat track, remove door sill scuff plate and disconnect wire connector.

AG-BODY 23 - 63

(7)Remove bolts holding seat track to cross mem-

ber.

(8)Remove seat from vehicle.

INSTALLATION

Reverse the preceding operation.

Fig. 28 Manual Front Seat

Fig. 29 Power Front Seat

REAR SEATS

REMOVAL (FIG. 30)

(1)Hinge seat backs forward.

(2)Remove bolts holding rear seat frame to floor on sides of center floor hump near luggage compartment kick-up.

(3)Pull seat forward to disengage retaining hooks from floor.

(4)Separate seat from vehicle.

23 - 64 AG-BODY

INSTALLATION

Reverse the preceding operation.

Fig. 30 Rear Seat Cushion and Back

FRONT CENTER CONSOLE

REMOVAL (FIG. 31)

(1)Position front seats full forward.

(2)Remove rear ash tray.

(3)Remove rear lower carpeted end cover.

(4)Remove nuts holding console to floor bracket.

(5)Position front seats full rearward.

(6)Raise console storage bin cover and remove bottom mat.

(7)Remove screws holding bottom of storage bin to floor bracket.

(8)Remove screws holding console side panels to instrument panel. Disengage hook and loop fasteners and separate side panels from console.

(9)Disconnect shift indicator cable and clips from shift mechanism through right side panel opening, if equipped with automatic transaxle. Refer to Group 8E, Instrument Panel and Gauges for proper procedures.

(10)Disengage clips holding parking brake lever cover to console and separate cover from vehicle.

(11)Remove center instrument panel bezel. Refer to Group 8E, Instrument Panel. Remove screws holding console to instrument panel.

(12)Remove screws holding console to lower instrument panel.

(13)Remove bolts holding console to forward floor mounting bracket.

(14)Remove gear selector knob.

(15)Separate console from floor and remove from vehicle.

INSTALLATION

Reverse the preceding operation.

Ä

Fig. 31 Center Console

FLOOR CARPET

REMOVAL (FIG. 32)

(1)Remove cowl trim panels and scuff plates.

(2)Remove front seats and inboard seat belts.

(3)Remove center arm rest and front console.

(4)Remove inboard and outboard seat belt lower attaching bolts.

(5)Remove left dash panel foot rest.

(6)Remove rear seat.

(7)Pull carpet from under quarter trim covers.

(8)Fold carpet and remove through door opening.

INSTALLATION

Reverse the preceding operation.

Fig. 32 Floor Carpet and SilencersÐTypical

Ä

OVERHEAD CONSOLE

REMOVAL (FIG. 33)

(1)Remove screws holding overhead console to reinforcement bracket.

(2)Slide overhead console rearward to separate reinforcement bracket retainer tab from console.

(3)Lower console from roof and disconnect wire connectors.

INSTALLATION

Reverse The preceding operation.

Fig. 33 Overhead ConsoleÐTypical

HEAD LINING

REMOVAL

(1)Disconnect battery negative cable.

(2)Pull dome lamp downward to disengage from retaining ring in head lining. Separate lens from lamp body and remove bulb. Separate bulb holder from lamp body. Remove attaching screw holding retaining ring to roof bow, if equipped.

(3)Remove screws holding coat hooks to roof above quarter panels.

(4)Remove roof rail and A-pillar mouldings.

(5)Remove screws holding sun visors to roof header and disconnect wire connector, if equipped. Remove inboard sun visor hangers.

(6)Remove overhead console, if equipped.

(7)Pull front reading lamp downward to disengage from retaining ring in head lining and disconnect wire connector. Remove screws holding retaining ring to roof header, if equipped.

(8)Remove pinch welt holding headlining to sun roof opening, if equipped.

(9)Remove screws holding lift gate opening header moulding to rear roof header. Separate moulding from header.

(10)Remove one quarter trim panel as necessary to clear head lining removal path.

(11)Remove head lining from vehicle.

AG-BODY 23 - 65

INSTALLATION

Reverse the preceding operation.

SUNROOF LIFT CONTROL

REMOVAL (FIG. 34)

(1)Remove sunroof glass panel. Refer to Owners manual for proper procedures.

(2)Remove pinch welt holding head lining to edge of sunroof opening.

(3)Remove trim ring from tilt control handle.

(4)Remove screws holding tilt control handle to tilt control. Separate handle from control.

(5)Remove nuts holding lift control to roof panel. Separate lift control from roof.

INSTALLATION

Reverse the preceding operation.

REAR WINDOW GLASS

The rear window moulding often cannot be salvaged after removal operation is completed. Verify moulding availability from the parts supplier before removing moulding.

REMOVAL (FIG. 35)

(1)Remove rear window moulding.

(2)Remove lift gate trim as necessary to gain access to rear window defogger wire connector and ground screw, if equipped.

WARNING: WEAR EYE AND HAND PROTECTION WHEN HANDLING SAFETY GLASS. PERSONAL INJURY CAN RESULT.

CAUTION: Do not damage body or trim finish when cutting out glass or applying fence primer.

(3)Cut the urethane around the perimeter of the back window glass. Refer to Windshield section of this group for proper procedures.

(4)Separate the rear window from the vehicle.

INSTALLATION

(1)Prepare the work area, window fence, and glass the same way as described in the Windshield section of this group.

(2)Place the fence spacers at the locations shown (Fig. 35).

(3)Apply a 10 mm (0.4 in.) bead of urethane around the perimeter of the glass.

(4)Install the glass in the same manner described in the Windshield section of this group.

(5)Install the rear window moulding. Apply 50 mm (2 in.) masking tape over moulding to assure alignment.

(6)Connect rear window defogger wiring and install lift gate trim.