Файл: 92FWD_23.pdf

23 - 34 AA-BODY

bottom trunk lid to hinge attaching bolts. Separate the trunk lid from the vehicle.

INSTALLATION

Reverse the preceding operation.

Fig. 53 Trunk Lid

TRUNK LID HINGE

REMOVAL (FIG. 54)

(1)Remove rear deck filler panel.

(2)Disconnect trunk lid lift torsion bars from hinges.

(3)Mark all attaching bolt, nut, and component locations with a suitable marking device. Use marks as a reference when installing hinge.

(4)Remove bolts holding trunk lid to hinge.

(5)Remove nuts and bolts holding hinge to closure panel below rear window glass.

(6)Separate hinge from vehicle.

INSTALLATION

Reverse the preceding operation.

Fig. 54 Trunk Lid Hinge

Ä

TRUNK LID TORSION BAR

REMOVAL (FIG. 54)

(1)Raise and support trunk lid in the full up posi-

tion.

(2)Remove trunk lining as necessary to gain access to torsion bars.

(3)Disengage adjusting end of torsion bar from the slot in the tension adjustment bracket.

(4)Pivot torsion bar out of lift arm swivel.

(5)Disconnect torsion bar from hinge.

INSTALLATION

Reverse the preceding operation.

TRUNK LID LATCH

REMOVAL (FIG. 55)

(1)Raise trunk lid to the full up position.

(2)Remove screws holding trim cover to latch and separate cover from vehicle.

(3)Disconnect remote release cable from latch.

(4)Disconnect trunk lock linkage rod from trunk latch, on AA-P and D models.

(5)Remove bolts holding latch to trunk lid and separate latch from vehicle.

INSTALLATION

Insert trunk lock chill into latch release driver, on AA-C models and reverse the preceding operation.

Fig. 55 Trunk Lid Latch

TRUNK LID LOCK

REMOVAL (FIG. 56)

AA-P/D MODELS

(1)Remove trunk lid tail light assembly. Refer to Group 8L, Lamps for proper procedures.

(2)Remove screws holding latch release linkage cover to trunk lid and separate cover from vehicle.

(3)Disconnect linkage rod from lock cylinder lever.

(4)Remove nut holding lock cylinder to trunk lid and separate lock from vehicle.

INSTALLATION

Reverse the preceding operation.

REMOVAL (FIG. 56)

AA-C MODELS

(1)Remove trunk lid tail light assembly. Refer to Group 8L, Lamps for proper procedures.

(2)Remove trunk latch.

(3)Remove bolts holding lock cylinder and chill to trunk lid and separate the lock from the vehicle.

INSTALLATION

Reverse the preceding operation.

Fig. 56 Trunk Lid Lock

TRUNK OPENING WEATHERSTRIP

REMOVAL(FIG. 57)

(1)Raise trunk lid to the full up position.

(2)Pull the weatherstrip from the pinch flange around the trunk opening.

INSTALLATION

A new trunk lid opening weatherstrip should be heated to approximately 38° C (100° F) before installing. The weatherstrip butt splice should be located at the center rear of trunk opening. Reverse the removal operation. After weatherstrip has been installed, close trunk lid and allow weatherstrip to cool. The weatherstrip will form to the trunk lid contour as it cools.

TRUNK LINING

REMOVAL (FIG. 58)

(1)Remove spare tire and emergency jack from the spare tire well.

(2)Remove screws holding trunk lining to tail closure panel.

(3)Remove screws holding trunk lining to inner quarter panels.

(4)Remove push-in fasteners holding lining to rear seat bulkhead. Remove seat back silencer, if equipped.

Fig. 57 Trunk Opening Weatherstrip

(5)Remove push-in fasteners holding rear seat back carpet covers to floor pan, if equipped with 60/40 rear seat back.

(6)Fold trunk lining inward, away from quarter panels and remove lining from vehicle.

INSTALLATION

Route the fuel fill door emergency release cable around rear edge of trunk lining side panel and reverse the removal operation.

Fig. 58 Trunk Lining

TRUNK LID LUGGAGE RACK

REMOVAL (FIG. 59)

(1)Remove screws holding cross bar to outboard skid strips.

(2)Pry rubber inserts from skid strips.

(3) Remove screws holding skid strips to trunk lid.

INSTALLATION

Reverse the preceding operation

Fig. 59 Trunk Lid Luggage Rack

FUEL FILL DOOR

REMOVAL (FIG. 60)

(1)Open fuel fill door.

(2)Separate trunk lining from right quarter panel.

(3)Remove nuts holding fuel fill door to quarter panel.

(4)Separate fuel fill door from quarter panel open-

ing.

INSTALLATION

Reverse the preceding operation. Align to achieve equal spacing around fuel fill door and flush to the quarter panel.

Fig. 60 Fuel Fill Door

GRILLE AC/D or AC/C-H BODY

GRILLE REMOVAL (FIG. 1)

(1)Remove screws holding grille to grille opening panel.

(2)Separate grille from vehicle.

GRILLE INSTALLATION

Reverse the preceding operation.

Fig. 1 GrilleÐAC/D Body

GRILLE EXTENSION MOULDING

REMOVAL (FIG. 1)

(1)Raise vehicle and support on safety stands if necessary.

(2)Remove nuts holding moulding to grille opening panel from behind fascia below headlamps.

(3)Separate moulding from vehicle.

INSTALLATION

Reverse the preceding operation.

GRILLE OPENING PANEL AC/D and AC/C-H BODY

GRILLE OPENING PANEL REMOVAL (FIG. 2)

(1)Remove grille.

(2)Disconnect wire connectors from all front end lighting.

(3)Remove front end splash shields as necessary to gain access to grille opening panel attaching nuts behind front fenders.

(4)Remove nuts holding grille opening panel to front fenders.

(5)Remove bolts holding grille opening panel to center support brace behind grille.

(6)Separate grille opening panel from vehicle.

GRILLE OPENING PANEL INSTALLATION

Reverse the preceding operation.