Файл: 92FWD_23.pdf

WHEEL OPENING AND BODY SIDE MOULDING REMOVAL AND INSTALLATION (FIG. 38)

FRONT FENDER

(1)Remove screws holding wheel opening moulding to front fender.

(2)Pry bottom of body side moulding from clip on front fender using a suitable trim stick. Lift moulding from clip and separate from fender.

(3)Replace damaged moulding clip weld studs with repair screws. Paint bare metal surfaces behind moulding to avoid rust.

(4)Position moulding in wheel opening and start top center screw of wheel opening moulding.

(5)Hook top of body side moulding over clip and snap bottom of moulding onto clip.

(6)Install screws around wheel opening.

DOORS

(1)Pry bottom of body side moulding from clips on door using a suitable trim stick. Lift moulding from clip and separate from door.

(2)Replace damaged moulding clip weld studs with repair screws. Paint or undercoat bare metal surfaces behind moulding to avoid rust.

(3)Position moulding on door in design location.

(4)Hook top of moulding over clips and snap bottom of moulding onto clips.

QUARTER PANEL

(1)Remove screws holding wheel opening moulding to quarter panel.

(2)Pry bottom of body side moulding from clip on quarter panel using a suitable trim stick. Lift moulding from clip and separate from fender.

(3)Replace damaged moulding clip weld studs with repair screws. Paint or undercoat bare metal surfaces behind moulding to avoid rust.

(4)Position moulding in wheel opening and start top center screw of wheel opening moulding.

(5)Hook top of body side moulding over clip and snap bottom of moulding onto clip.

(6)Install screws around wheel opening.

APPLIQUE MOULDING AND RETAINER REMOVAL (FIG. 38)

(1)Remove screws holding applique to rocker panel from under vehicle.

(2)Lift applique upward to separate from retaining channel.

(3)Remove pop-rivets holding retainer to rocker panel using a suitable drill.

APPLIQUE MOULDING AND RETAINER INSTALLATION

(1) Install applique retainer on rocker panel with pop-rivets. Paint or undercoat bare metal surfaces to avoid rust.

(2) Hook top of applique over retainer channel and install screws under rocker panel.

COWL PANEL TRIM AND SCUFF PLATES

COWL PANEL AND DOOR OPENING SCUFF PLATE REMOVAL (FIG. 39)

(1)Open front door.

(2)Remove screw holding trim panel to cowl forward of the front door opening.

(3)Remove screws holding scuff plate to door sill.

(4)Separate cowl panel trim and scuff plate from vehicle.

COWL PANEL AND DOOR OPENING SCUFF PLATE INSTALLATION

Reverse the preceding operation.

REAR DOOR OPENING SCUFF PLATE REMOVAL (FIG. 39)

(1)Open rear door.

(2)Remove screws holding scuff plate to door sill.

(3)Separate scuff plate from vehicle.

REAR DOOR OPENING SCUFF PLATE INSTALLATION

Reverse the preceding operation.

A-PILLAR AND ROOF RAIL MOULDINGS

A-PILLAR MOULDING REMOVAL (FIG. 39)

(1)Open front door.

(2)Disengage clips holding A-pillar moulding to roof rail above door opening.

(3)Slide A-pillar moulding upward and pull rearward to separate moulding from A-pillar.

A-PILLAR MOULDING INSTALLATION

Reverse the preceding operation.

REAR DOOR ROOF RAIL MOULDING REMOVAL (FIG. 39)

(1)Open rear door.

(2)Disengage clips holding roof rail moulding to roof rail above rear door opening.

(3)Separate moulding from vehicle.

REAR DOOR ROOF RAIL MOULDING INSTALLATION

Reverse the preceding operation.

B-PILLAR TRIM PANEL

B-PILLAR TRIM PANEL REMOVAL (FIG. 39)

(1)Remove roof rail mouldings and scuff plates as necessary.

(2)Remove shoulder harness turning loop cover. Remove bolt holding turning loop to B-pillar.

Ä

(3)Remove bolt holding seat belt to floor below B-pillar.

(4)Lift B-pillar trim off door opening sill weatherstrips and push inward.

(5)Slide B-pillar trim downward as far as possible and separate trim from B-pillar.

B-PILLAR TRIM PANEL INSTALLATION

Reverse the preceding operation.

QUARTER TRIM PANEL

REMOVAL (FIG. 39)

(1)Remove roof rail mouldings and scuff plates as necessary.

(2)Remove shoulder harness turning loop cover. Remove bolt holding turning loop to quarter panel.

(3)Remove rear seat cushion, back, and rear bol-

ster.

(4)Remove push-in fastener holding quarter trim to roof rail.

(5)Remove screws holding quarter trim panel to wheelhouse kickup.

(6)Pull trim panel forward and separate from ve-

hicle.

INSTALLATION

Reverse the preceding operation.

QUARTER EXTENSION TRIM PANEL

REMOVAL (FIG. 39)

(1) Remove rear seat cushion, back, and rear bolster.

AA-BODY 23 - 27

(2)Disengage clips holding expansion trim panel to shelf panel.

(3)Separate trim panel from vehicle.

INSTALLATION

Reverse the preceding operation.

REAR SHELF TRIM PANEL

REMOVAL (FIG. 39)

(1)Remove one quarter trim panel.

(2)Remove center high mounted stop lamp cover. Refer to Group 8L, Lamps for instructions.

(3)Disengage frog leg fasteners holding trim to shelf panel and separate trim from vehicle.

INSTALLATION

Reverse the preceding operation.

FRONT SEAT BELTS

OUTBOARD SHOULDER HARNESS/LAP BELT REMOVAL (FIG. 40)

(1)Remove B-pillar trim panel.

(2)Remove bolt holding seat belt retractor to B-pillar.

(3)Separate retractor from vehicle.

OUTBOARD SHOULDER HARNESS/LAP BELT INSTALLATION

Reverse the preceding operation.

23 - 28 AA-BODY

INBOARD BUCKLE/CENTER OCCUPANT BELTS REMOVAL (FIG. 40)

Vehicles equipped with front bucket seats with center console do not have center occupant belts.

(1)Remove bolt holding inboard buckle/center occupant belt to floor.

(2)Disconnect seat belt sensor wire connector.

(3)Separate buckle/belt assembly from vehicle.

INBOARD BUCKLE/CENTER OCCUPANT BELT INSTALLATION

Reverse the preceding operation.

Fig. 40 Front Seat Belts

REAR SEAT BELTS

OUTBOARD SHOULDER HARNESS/LAP BELT REMOVAL (FIG. 41)

(1)Remove quarter trim panel.

(2)Remove bolt holding lap belt to floor at wheelhouse kickup.

(3)Remove bolt holding seat belt retractor to quarter panel.

OUTBOARD SHOULDER HARNESS/LAP BELT INSTALLATION

Reverse the preceding operation.

INBOARD BUCKLE/CENTER OCCUPANT BELTS REMOVAL (FIG. 41)

(1)Remove rear seat cushion.

(2)Remove bolt holding inboard buckle/center occupant belt to floor.

(3)Separate buckle/belt assembly from vehicle.

Ä

INBOARD BUCKLE/CENTER OCCUPANT BELT INSTALLATION

Reverse the preceding operation.

Fig. 41 Rear Seat Belts

FRONT SEATS

REMOVAL (FIG. 42 OR 43)

(1)Position seat full forward.

(2)Remove screws holding rear track riser covers and separate covers from tracks.

(3)On power seat track, remove outboard track

cover.

(4)On 50/50 seats, remove inboard seat belt attaching bolt from floor.

(5)Remove nuts holding seat track to floor.

(6)Position seat full rearward.

(7)On power seat track, remove door sill scuff plate and disconnect wire connector.

(8)Remove bolts holding seat track to cross mem-

ber.

(9)Remove seat from vehicle.

INSTALLATION

Reverse the preceding operation.

REAR SEATS

REAR SEAT CUSHION REMOVAL

(1)Remove bolts holding cushion to floor.

(2)Push center occupant seat belts through openings in cushion.

(3)Remove cushion from vehicle.

REAR SEAT CUSHION INSTALLATION

Reverse the preceding operation.

Ä

Fig. 42 Manual Front Seat

Fig. 43 Power Front Seat

REAR SEAT BACK REMOVAL (FIG. 44)

(1)Hinge seat back forward and disengage push-in fasteners holding carpet backing to trunk floor.

(2)Remove bolts holding outboard hinge pivot bracket to seat back.

(3)Pull seat back outward to disengage inboard pivot and separate from vehicle.

REAR SEAT BACK INSTALLATION

Reverse the preceding operation.

SEAT BACK BOLSTER CUSHION REMOVAL (FIG. 44)

(1)Remove rear seat cushion and back as neces-

sary.

(2)Remove bolts holding outboard back bolster to quarter panel.

(3)Lift bolster upward to disengage hook retainer on back of bolster and separate from vehicle.

AA-BODY 23 - 29

SEAT BACK BOLSTER CUSHION INSTALLATION

Reverse the preceding operation

Fig. 44 Rear Seat Cushion and Back

FRONT CENTER CONSOLE

REMOVAL (FIG. 45)

(1)Position front seats full forward.

(2)Remove access hole plugs on sides of center arm rest riser and remove bolts holding riser to floor bracket.

(3)Remove coin holder and remove screws holding arm rest riser to front console.

(4)Position front seats full rearward.

(5)Remove radio bezel from instrument panel. Refer to Group 8E, Instrument Panel. Remove screws holding console to instrument panel.

(6)Remove screws holding console to lower instrument panel rail.

(7)Remove screws and disengage hook and loop fastener holding carpet panels to sides of console and separate panels from console.

(8)Remove screws holding console to forward floor mounting bracket.

(9)Remove set screw holding gear selector knob to shift lever and pull knob from shifter on vehicles with automatic transaxle.

(10)Lift forward edge of PRNDL cover and separate cover from console on vehicles with automatic transaxle.

(11)Lift gear shift boot adapter from console and push adapter through opening in console on vehicles with manual transaxle.

(12)Separate console from floor and remove from vehicle.