Файл: 92FWD_23.pdf

23 - 30 AA-BODY

INSTALLATION

Reverse the preceding operation. On vehicles with automatic transaxle, verify gear selector indicator adjustment before returning vehicle to use.

Fig. 45 Front Center Console

FLOOR CARPET

REMOVAL (FIG. 46)

(1)Remove cowl trim panels and scuff plates.

(2)Remove front seats and inboard seat belts.

(3)Remove center arm rest and front console.

(4)Remove outboard seat belt lower attaching

bolts.

(5)Remove rear seat cushion.

(6)Pull carpet from under B-pillar trim covers.

(7)Fold carpet and remove through front door opening.

INSTALLATION

Reverse the preceding operation.

Fig. 46 Floor Carpet and Silencers

Ä

OVERHEAD CONSOLE

REMOVAL (FIG. 47)

(1)Remove screws holding overhead console to reinforcement bracket.

(2)Slide overhead console rearward to separate reinforcement bracket retainer tab from console.

(3)Lower console from roof and disconnect wire connectors.

INSTALLATION

Reverse The preceding operation.

Fig. 47 Overhead Console

HEAD LINING

REMOVAL (FIG. 48)

(1)Disconnect battery negative cable.

(2)Pull dome lamp downward to disengage from retaining ring in head lining. Separate lens from lamp body and remove bulb. Separate bulb holder from lamp body. Remove attaching screw holding retaining ring to roof bow.

(3)Remove screws holding coat hooks to roof above rear doors.

(4)Remove roof rail and A-pillar mouldings.

(5)Remove screws holding sun visors to roof header and disconnect wire connector, if equipped. Remove inboard sun visor hangers.

(6)Remove overhead console, if equipped.

(7)Pull front reading lamp downward to disengage from retaining ring in head lining and disconnect wire connector. Remove screws holding retaining ring to roof header.

(8)Remove pinch welt holding headlining to sun roof opening, if equipped.

(9)Remove inside rear view mirror from windshield bracket if necessary.

(10)Disengage hook and loop fasteners holding head lining to roof above rear window and slide head lining forward about 25 mm (1 in.).

Ä

(11)Shift the front of head lining to one side to pull head lining from behind B-pillar trim. Pull head lining from behind other B-pillar trim.

(12)Allow front of head lining to drop downward. Slide head lining forward from behind quarter panel trim.

(13)Remove head lining from vehicle.

INSTALLATION

Reverse the preceding operation.

Fig. 48 Head Lining

SUN ROOF WEATHERSTRIP

REMOVAL (FIG. 49)

(1)Remove sun roof sunshade and glass. Refer to Owner's Manual for instructions.

(2)Pull weatherstrip from pinch flange around sun roof opening.

INSTALLATION

Reverse the preceding operation.

SUN ROOF AIR DEFLECTOR

REMOVAL (FIG. 49)

(1)Remove sun roof sunshade and glass. Refer to Owner's Manual for instructions.

(2)Disengage snap-on linkage at rear of air deflector in sun roof opening.

(3)Remove screws holding air deflector to front of sun roof opening.

INSTALLATION

Reverse the preceding operation.

AA-BODY 23 - 31

SUN ROOF DRAIN TUBES

REMOVAL (FIG. 49)

(1)Remove head lining as necessary.

(2)Remove A-pillar or B-pillar trim covers as necessary.

(3)Remove cowl panel and sill plate trim as neces-

sary.

(4)Disconnect effected drain tube from nipple at sun roof opening.

(5)Pull drain tube upward to remove from pillar involved.

INSTALLATION

Reverse the preceding operation. Route the tube to avoid kinks or puncture from sharp edges.

VINYL ROOF BONNET

REMOVAL (FIG. 50)

(1)Remove quarter panel trim covers.

(2)Remove head lining.

(3)Remove nuts holding transverse roof moulding to roof panel and separate moulding from vehicle.

(4)Remove nuts holding vinyl top bonnet to roof.

(5)Remove rear deck filler panel.

(6)Remove screws holding rear window opening lower valance to body.

(7)Disengage hook and loop fasteners holding vinyl top bonnet to quarter panels.

(8)Pull vinyl top bonnet away from top panel to separate bonnet from anti-flutter sealer holding bonnet to roof.

INSTALLATION

(1)Clean anti-flutter sealer from roof surface and inside of vinyl roof bonnet.

(2)Apply a 20 mm (0.75 in.) bead of anti-flutter sealer across the roof panel at the mid point between the front of the bonnet and rear of roof.

(3)Apply a 20 mm (0.75 in.) by 150 mm (6 in.) bead of anti-flutter sealer down each roof side panel at mid point between the door opening and rear of roof.

(4)Place the bonnet into position on the roof panel and align to proper fit.

(5)Reverse the removal operation.

REAR DECK FILLER PANEL

REMOVAL (FIG. 51)

(1)Raise truck lid to full up position.

(2)Remove screws holding rear deck filler panel to body in the front trunk opening gutter.

(3)Close trunk lid, do not latch.

(4)Lift filler panel upward and separate from ve-

hicle.

Fig. 50 Vinyl Roof Bonnet

INSTALLATION

Reverse the preceding operation.

Fig. 51 Rear Deck Filler Panel

REAR WINDOW GLASS

REMOVAL (FIG. 52)

The rear window moulding often cannot be salvaged after removal operation is completed. Verify moulding availability from the parts supplier before removing moulding.

(1)Remove rear deck filler panel.

(2)Pull rear window moulding from between glass and roof panel.

(3)Remove interior trim as necessary to gain access to rear window defogger wire connector and ground screw, if equipped.

(4)Remove vinyl roof bonnet, if equipped.

WARNING: WEAR EYE AND HAND PROTECTION WHEN HANDLING SAFETY GLASS. PERSONAL INJURY CAN RESULT.

CAUTION: Do not damage body or trim finish when cutting out glass or applying fence primer.

(5)Cut the urethane around the perimeter of the rear window glass. Refer to Windshield section of this group for proper procedures.

(6)Separate the rear window from the vehicle.

INSTALLATION

(1)Prepare the work area, window fence, and glass the same way as described in the Windshield section of this group.

(2)Place the fence spacers at the locations shown (Fig. 52).

(3)Apply a 10 mm (0.4 in.) bead of urethane around the perimeter of the glass.

(4)Install the glass in the same manner described in the Windshield section of this group.

(5)Install the rear window moulding in the gap between the glass and the roof panel.

(6)Secure moulding and glass in position with suitable tape. Remove tape after urethane has cured.

(7)Connect rear window defogger wiring. Install interior trim and rear deck filler panel.

(8)After urethane has cured, water test rear window to verify repair. Verify rear window defogger operation, see Group 8N, Rear Window Defogger.

TRUNK LID

REMOVAL (FIG. 53)

(1)Raise trunk lid to full up position.

(2)Disconnect the trunk lamp wire connector.

(3)Mark all bolt and hinge attachment locations with a grease pencil or other suitable device to provide reference marks for installation. When installing trunk lid, align all marks and secure bolts. The trunk lid should be aligned to 4 mm (0.160 in.) gap to the quarter panels and flush across the top surfaces along quarter panels.

(4)Remove the top trunk lid to hinge attaching bolts and loosen the bottom bolts until they can be removed by hand.

(5)With assistance of a helper at the opposite side of the vehicle to support the trunk lid, remove the