Файл: 92FWD_23.pdf

(7) After urethane has cured remove masking tape and water test to verify repair. Verify rear window defogger operation, refer to Group 8N, Rear Window Defogger.

QUARTER GLASS MODULE

REMOVAL (FIG. 36)

(1)Remove quarter trim panel as necessary to gain access to quarter glass module.

(2)Remove nuts holding quarter glass module to quarter glass opening.

(3)Cut urethane bonding around perimeter of quarter glass opening fence.

(4)Push quarter glass module from quarter glass opening.

(5)Separate module from vehicle.

INSTALLATION

(1)Clean hardened urethane from quarter glass opening fence and glass module, if module replacement is not required.

(2)Prepare fence and module using method described in the Windshield section of this group.

(3)Reverse the removal operation.

ROOF SEAM MOLDING

REMOVAL (FIG. 37)

(1) Remove upper quarter trim panel.

Fig. 36 Quarter Glass Module

(2)Remove head lining as necessary to gain access to inside roof panel.

(3)Remove seal nut holding seam molding to roof panel.

(4)Separate molding from roof panel.

INSTALLATION

Reverse the preceding operation.

Fig. 37 Roof Seam Molding

QUARTER PANEL SPOILER

REMOVAL (FIG. 38)

(1)Remove access cover from lift gate opening end of quarter panel spoiler.

(2)Remove bolt holding spoiler to tail lamp closure panel.

(3)Remove quarter trim panel.

(4)Remove nuts holding spoiler to quarter panel from behind quarter panel above rear wheelhouse (Fig. 38).

(5)Separate spoiler from vehicle.

INSTALLATION

Reverse the preceding operation.

Fig. 38 Quarter Panel Spoiler

LIFT GATE SPOILER

REMOVAL (FIG. 39)

(1)Raise lift gate to the up position.

(2)Remove nuts holding spoiler to outboard pinch flanges of lift gate.

(3)Separate spoiler from lift gate.

INSTALLATION

Reverse the preceding operation.

Fig. 39 Lift Gate Spoiler

LIFT GATE PROP CYLINDER

REMOVAL (FIG. 40)

(1)raise lift gate to the full open position.

(2)Support lift gate on a suitable lifting device.

(3)Remove bolt holding bottom of lift gate prop cylinder to c-pillar.

(4)Remove bolt holding top of lift gate prop cylinder to lift gate.

(5)Separate prop cylinder from vehicle.

INSTALLATION

Reverse the preceding operation.

23 - 68 AG-BODY

Fig. 40 Lift Gate Prop Cylinder

LIFT GATE

REMOVAL (FIG. 41)

(1)Raise lift gate to the full open position.

(2)Remove rear roof header molding.

(3)Disconnect lift gate wire connectors and rear window washer hose, if equipped.

(4)Remove upper lift gate trim molding.

(5)Support lift gate on a suitable lifting device.

(6)Disconnect top of prop cylinders from lift gate.

(7)Mark lift gate hinge locations to assist installation an alignment of lift gate.

(8)With assistance of a helper, remove bolts holding lift gate to hinge.

(9)Separate lift gate from vehicle.

INSTALLATION

Reverse the preceding operation.

Fig. 41 Lift Gate

LIFT GATE LATCH AND STRIKER

LIFT GATE LATCH REMOVAL (FIG. 42)

(1)Raise lift gate to the full open position.

(2)Remove luggage compartment tail trim panel.

(3)Disconnect lock linkage rod from lift gate latch

arm.

(4)Remove nuts holding lift gate latch to tail panel.

Ä

(5) Separate latch from tail panel and disconnect lift gate remote release cable.

LIFT GATE LATCH INSTALLATION

LIFT GATE STRIKER REMOVAL (FIG. 42)

(1)Raise lift gate to the full open position.

(2)Remove lower lift gate trim panel.

(3)Mark lift gate striker location to assist installa-

tion.

(4)Remove bolts holding lift gate striker to lift

gate.

(5)Separate striker from lift gate.

LIFT GATE STRIKER INSTALLATION

Reverse the preceding operation.

Fig. 42 Lift Gate Latch and Striker

LIFT GATE LOCK CYLINDER

REMOVAL (FIG. 43)

(1)Raise lift gate to the full open position.

(2)Remove luggage compartment tail trim panel.

(3)Disconnect linkage return spring (Fig. 42).

(4)Disconnect linkage rod from lift gate lock arm.

(5)Remove bolts holding lift gate lock to tail panel.

(6)Separate lock from tail panel.

INSTALLATION

Reverse the preceding operation.

FUEL FILL DOOR

REMOVAL (FIG. 44)

(1)Remove right lower quarter trim panel.

(2)Open fuel fill door.

(3)Remove nuts holding fuel fill door to quarter panel from in luggage compartment.

(4)Separate fuel fill door from vehicle.

INSTALLATION

Reverse the preceding operation

Fig. 43 Lift Gate Lock Cylinder

LIFT GATE AND FUEL FILL DOOR RELEASE CABLES

LIFT GATE AND FUEL FILL DOOR CABLES REMOVAL (FIG. 45)

(1)Remove interior trim as necessary to gain access to release cables.

(2)Remove left front door opening scuff plate.

(3)Remove screw holding trim cover to release cable handle and separate cover from handle.

(4)Remove screw holding release handle to door

sill.

(5)Pry open retainer tab holding cable core end in handle pivot. Pry cable case end from handle.

(6)On fuel fill door cable, remove nut holding cable latch to fuel fill opening.

Fig. 44 Fuel Fill Door

(7) On lift gate latch, remove lift gate latch cover and disconnect cable end from latch. Route cable back through trunk lid.

LIFT GATE AND FUEL FILL DOOR CABLES INSTALLATION

Reverse the preceding operation.

TAIL LAMP CLOSURE PANEL

REMOVAL

(1)Remove lift gate opening scuff plate.

(2)Remove lift gate opening sill cover.

(3)Remove luggage compartment tail panel trim.

(4)Remove lower quarter trim panels.

(5)Remove bolt holding quarter panel spoiler to tail lamp closure panel, if equipped.

23 - 70 AG-BODY

(6)Remove tail lamps and license plate lamps, refer to Group 8L, Lamps for proper procedures.

(7)Remove nuts holding tail lamp closure panel to tail panel.

(8)Remove nuts holding tail lamp closure panel to quarter panel ends.

(9)Separate tail lamp closure panel from vehicle.

INSTALLATION

Reverse the preceding operation.

Ä

Fig. 46 Tail Lamp Closure Panel