Файл: 92FWD_23.pdf

(6)Remove quarter trim extension panel. Remove screws holding quarter trim panel to wheelhouse kickup.

(7)Remove rear reading lamp. Remove screw holding quarter trim to roof from lamp opening.

(8)Pull trim panel forward and separate from ve-

hicle.

QUARTER TRIM PANEL INSTALLATION

Reverse the preceding operation.

QUARTER EXTENSION TRIM PANEL

REMOVAL (FIG. 13)

(1)Remove quarter trim panel.

(2)Disengage clips holding expansion trim panel to shelf panel.

(3)Separate trim panel from vehicle.

INSTALLATION

Reverse the preceding operation.

(3) Disengage screws holding trim to shelf panel and separate trim from vehicle.

INSTALLATION

Reverse the preceding operation.

23 - 78 AJ-BODY

FRONT SEAT BELTS

OUTBOARD SHOULDER HARNESS/LAP BELT REMOVAL (FIG. 14)

(1)Remove quarter trim panel.

(2)Remove bolt holding seat belt retractor to quarter panel.

(3)Separate retractor from vehicle.

OUTBOARD SHOULDER HARNESS/LAP BELT INSTALLATION

Reverse the preceding operation.

INBOARD SEAT BELT BUCKLE REMOVAL (FIG. 14)

(1)Remove bolt holding inboard buckle to floor.

(2)Disconnect seat belt sensor wire connector.

(3)Separate buckle assembly from vehicle.

INBOARD SEAT BELT BUCKLE INSTALLATION

Reverse the preceding operation.

Fig. 14 Front Seat Belts

REAR SEAT BELTS

OUTBOARD SHOULDER HARNESS/LAP BELT REMOVAL (FIG. 15)

(1)Remove quarter trim panel.

(2)Remove bolt holding lap belt to floor at wheelhouse kickup.

(3)Remove bolt holding seat belt retractor to quarter panel.

Ä

OUTBOARD SHOULDER HARNESS/LAP BELT INSTALLATION

Reverse the preceding operation.

INBOARD BUCKLE/CENTER OCCUPANT BELTS REMOVAL (FIG. 15)

(1)Remove rear seat cushion.

(2)Remove bolt holding inboard buckle/center occupant belt to floor.

(3)Separate buckle/belt assembly from vehicle.

INBOARD BUCKLE/CENTER OCCUPANT BELT INSTALLATION

Reverse the preceding operation.

Fig. 15 Rear Seat Belts

FRONT SEATS

FRONT SEAT REMOVAL (FIG. 16 OR 17)

(1)Position seat full forward.

(2)Remove screws holding rear track riser covers and separate covers from tracks.

(3)On power seat track, remove outboard track

cover.

(4)Remove nuts holding seat track to floor.

(5)Position seat full rearward.

(6)On power seat track, remove door sill scuff plate and disconnect wire connector.

(7)Remove bolts holding seat track to cross mem-

ber.

(8)Remove seat from vehicle.

FRONT SEAT INSTALLATION

Reverse the preceding operation.

Fig. 16 Manual Front Seat

Fig. 17 Power Front Seat

REAR SEATS

REAR SEAT CUSHION REMOVAL

(1)Remove bolts holding cushion to floor.

(2)Push center occupant seat belts through openings in cushion.

(3)Remove cushion from vehicle.

REAR SEAT CUSHION INSTALLATION

Reverse the preceding operation.

REAR SEAT BACK REMOVAL (FIG. 18)

(1)Hinge seat back forward and disengage push-in fasteners holding carpet backing to trunk floor.

(2)Remove bolts holding outboard hinge pivot bracket to seat back.

(3)Pull seat back outward to disengage inboard pivot and separate from vehicle.

REAR SEAT BACK INSTALLATION

Reverse the preceding operation.

Fig. 18 Rear Seat Cushion and Back

FRONT CENTER CONSOLE

REMOVAL (FIG. 19)

(1)Position front seats full forward.

(2)Remove rear ash tray.

(3)Remove rear lower carpeted end cover.

(4)Remove nuts holding console to floor bracket.

(5)Position front seats full rearward.

(6)Raise console storage bin cover and remove bottom mat.

(7)Remove screws holding bottom of storage bin to floor bracket.

(8)Remove screws holding console side panels to instrument panel. Disengage hook and loop fasteners and separate side panels from console.

(9)Disconnect shift indicator cable and clip from shift mechanism through right side panel opening, if equipped with automatic transaxle. Refer to Group 8E, Instrument Panel and Gauges for proper service procedures.

(10)Disengage clips holding parking brake lever cover to console and separate cover from vehicle.

(11)Remove center instrument panel bezel. Refer to Group 8E, Instrument Panel. Remove screws holding console to instrument panel.

(12)Remove screws holding console to lower instrument panel.

(13)Remove bolts holding console to forward floor mounting bracket.

(14)Remove gear selector knob.

(15)Separate console from floor and remove from vehicle.

INSTALLATION

Reverse the preceding operation.

23 - 80 AJ-BODY

Fig. 19 Center Console

FLOOR CARPET

REMOVAL (FIG. 20)

(1)Remove cowl trim panels and scuff plates.

(2)Remove front seats and inboard seat belts.

(3)Remove center arm rest and front console.

(4)Remove outboard seat belt lower attaching

bolts.

(5)Remove left dash panel foot rest.

(6)Remove rear seat cushion.

(7)Pull carpet from under quarter trim covers.

(8)Fold carpet and remove through door opening.

INSTALLATION

Reverse the preceding operation.

Fig. 20 Floor Carpet and SilencersÐTypical

Ä

OVERHEAD CONSOLE

REMOVAL (FIG. 21)

(1)Remove screws holding overhead console to reinforcement bracket.

(2)Slide overhead console rearward to separate reinforcement bracket retainer tab from console.

(3)Lower console from roof and disconnect wire connectors.

INSTALLATION

Reverse The preceding operation.

Fig. 21 Overhead ConsoleÐTypical

HEAD LINING

REMOVAL

(1)Disconnect battery negative cable.

(2)Pull dome lamp downward to disengage from retaining ring in head lining. Separate lens from lamp body and remove bulb. Separate bulb holder from lamp body. Remove attaching screw holding retaining ring to roof bow, if equipped.

(3)Remove screws holding coat hooks to roof above quarter panels.

(4)Remove roof rail and A-pillar mouldings.

(5)Remove screws holding sun visors to roof header and disconnect wire connector, if equipped. Remove inboard sun visor hangers.

(6)Remove overhead console, if equipped.

(7)Pull front reading lamp downward to disengage from retaining ring in head lining and disconnect wire connector. Remove screws holding retaining ring to roof header, if equipped.

(8)Remove pinch welt holding headlining to sun roof opening, if equipped.

(9)Remove one quarter trim panel as necessary to clear head lining removal path.

(10)Disengage hook and loop fasteners holding head lining to roof above rear window and slide head lining from behind quarter panel.

(11)Remove head lining from vehicle.

Ä

INSTALLATION

Reverse the preceding operation.

SUN ROOF WEATHERSTRIP

REMOVAL (FIG. 22)

(1)Remove sun roof sunshade and glass. Refer to Owner's Manual for instructions.

(2)Pull weatherstrip from pinch flange around sun roof opening.

INSTALLATION

Reverse the preceding operation.

SUN ROOF AIR DEFLECTOR

REMOVAL (FIG. 22)

(1)Remove sun roof sunshade and glass. Refer to Owner's Manual for instructions.

(2)Disengage snap-on linkage at rear of air deflector in sun roof opening.

(3)Remove screws holding air deflector to front of sun roof opening.

INSTALLATION

Reverse the preceding operation.

AJ-BODY 23 - 81

SUN ROOF DRAIN TUBES

REMOVAL (FIG. 22)

(1)Remove head lining as necessary.

(2)Remove A-pillar or quarter trim covers as neces-

sary.

(3)Remove cowl panel and sill plate trim as neces-

sary.

(4)Disconnect effected drain tube from nipple at sun roof opening.

(5)Pull drain tube upward to remove from pillar involved.

INSTALLATION

Reverse the preceding operation. Route the tube to avoid kinks or puncture from sharp edges.

REAR WINDOW GLASS

REMOVAL (FIG. 23)

(1)Remove rear window mouldings.

(2)Remove interior trim as necessary to gain access to rear window defogger wire connector and ground screw, if equipped.

WARNING: WEAR EYE AND HAND PROTECTION WHEN HANDLING SAFETY GLASS. PERSONAL INJURY CAN RESULT.